Skip to content
Boilers.caby ROMA Heating & Cooling

Boiler type

Non-condensing (conventional) boilers

Non-condensing gas boilers, often called conventional or atmospheric boilers, keep their flue gases hot enough that they never condense, which protects a metal vent or chimney but forgoes the latent-heat recovery that makes modern boilers efficient. Most units still heating BC homes are older designs facing a repair-versus-replacement decision.

What a non-condensing boiler is

A non-condensing boiler is the conventional gas boiler design: fuel burns in a combustion chamber, the hot gases pass once or more through a heat exchanger, and the system water absorbs what it can before the gases are exhausted up a vent or chimney. The term conventional comes from the industry, and these boilers are sometimes called atmospheric because many rely on natural draft, drawing room air in through a draft hood and pushing flue gas up a chimney without a fan.

The defining engineering choice is to keep the flue gas hot, above its dew point, for the entire trip out of the building. If the gas cooled enough to condense inside the boiler, the acidic liquid would attack a cast-iron heat exchanger and the vent would have to be corrosion-proof plastic. Older designs therefore run their water temperatures high and send hot, buoyant exhaust up a metal vent or masonry chimney. That simplicity made them inexpensive and long-lived, and it is also the reason they give up the latent heat that condensing boilers recover.

How it differs from a condensing design

The practical differences follow from that one decision. A non-condensing boiler does not produce condensate, so it does not need a condensate drain or neutralizer, and its venting can be conventional: a listed metal vent, a chimney liner, or a masonry chimney where the flue is in good condition. Because the heat exchanger operates hot and dry, there is no corrosive liquid to manage inside the unit.

The trade-off is efficiency. Without flue-gas condensation, the boiler sends a meaningful share of its fuel's heat up the vent, and its efficiency rating sits below the roughly 95% AFUE that modern condensing gas boilers are typically rated at in Canada. Operating patterns differ too: non-condensing boilers generally run at a fixed high water temperature and cycle on and off against the thermostat rather than modulating down to match a mild load, which is a poor fit for the long, gentle shoulder seasons of coastal BC.

Designers also have to respect thermal mass and temperature. Cast-iron sectional blocks expand and contract with temperature, and pushing very cold return water into a hot boiler invites stress, so system design keeps return-water temperatures moderate. A condensing boiler instead wants the return as cool as it can get it, which is a reversal of the old logic that installers and plumbers trained on conventional boilers have to relearn.

Where non-condensing boilers still operate in BC

Non-condensing gas boilers in Greater Vancouver are mostly legacy equipment: cast-iron or steel units from the 1980s through the early 2000s, often sitting in basement utility rooms, venting into a chimney that may once have served an oil burner. Condominium and apartment plants from the same era commonly hold one or more conventional boilers tied to a shared vent and a common header.

None of this makes them unsafe or obsolete in the legal sense. A well-maintained conventional boiler can keep a home warm for a long time, and Technical Safety BC's guidance on annual servicing applies to all gas appliances: check the controls, burners, venting and flue, and the carbon-monoxide risk, every year. What changes is the decision point: when a conventional boiler fails, parts for older models get harder to source, and the repair-versus-replacement comparison usually lands on a condensing unit, because the venting, controls and water temperatures around the old boiler rarely suit a modern appliance anyway.

Repair, replacement and service realities

When a non-condensing boiler is serviced or repaired, the work that matters most happens outside the boiler. The chimney and vent connector should be inspected for soot, corrosion, gaps and blockage, because a blocked or damaged flue is what turns a functioning boiler into a carbon-monoxide hazard. Gas piping, the draft hood, burner and safety controls get the same scrutiny. This is the work a licensed gas contractor does as part of a service visit or repair, and it is not something a homeowner should attempt.

On the replacement side, a conventional boiler's chimney usually cannot be reused by its condensing successor, so the project scope grows: new certified plastic venting through a wall, condensate drainage, a sealed system with an expansion tank, and often new controls. The old boiler's removal is straightforward for a contractor, but anyone planning around an old unit should budget mentally for the full system change, not just the appliance.

Permits follow the same rules as any gas appliance: a gas permit is required for installation or replacement, homeowners in single-family homes can hold the permit themselves in the cases Technical Safety BC describes, and owners of strata units and duplexes must use a licensed contractor. In Burnaby and other municipalities that issue their own permits, the contractor confirms the local process before starting.

Questions to ask a contractor

If the boiler is still running, ask whether the repair is a single defined fault or one symptom of a unit that is wearing out, and ask how the contractor priced the repair against a replacement in writing. Ask whether the chimney and vent were inspected in the last year and what the inspection found, since flue condition often decides whether repair is even sensible.

If the conversation turns to replacement, ask why the proposed boiler is a condensing unit, how it will vent, where its condensate will drain, and whether the existing radiators can run at the lower temperatures that make it condense. Ask who applies for the gas permit and, where the municipality issues one, the heating permit. The buying guide on this site compares the options in detail, and the consultation service on this site can review the repair-versus-replacement numbers for a specific property.

Frequently asked questions

Should I repair my old conventional boiler or replace it?

A single well-defined fault on a unit in good overall shape can justify a repair. Repeated faults, a cracked heat exchanger, unavailable parts or a failing vent usually do not. Ask for a written repair-versus-replacement recommendation with the reasons.

Can a non-condensing boiler keep using its chimney?

Yes, that is the point of the design: it exhausts hot gas that a lined chimney or listed metal vent can handle. The chimney still needs annual inspection, because cracks, soot and blockage are what create carbon-monoxide risk.

Is a non-condensing boiler less efficient than a condensing one?

In rated terms, yes: it does not recover the latent heat of the flue-gas vapour, so its rating sits below the roughly 95% AFUE typical of modern condensing boilers, and it usually runs hotter and cycles more. Actual behaviour depends on the system, as the buying guide on this site explains.

Book a consultation

A technician reviews your building and options. Requests are confirmed by ROMA.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate