Boiler type
System boilers (heating-only with indirect tank)
In North American usage, a system boiler means a sealed, heating-only gas boiler that makes domestic hot water by heating a separate indirect storage tank through a coil. The term is used differently in the United Kingdom, so this page explains the naming and how the arrangement works.
What the term means in North America
The phrase system boiler is imported from the United Kingdom, where it has a specific meaning: a sealed-system boiler that heats radiators and also feeds a separate hot-water cylinder, with the pump and expansion vessel built in. In North America the term is used more loosely, and on this site it means a heating-only gas boiler connected to an indirect domestic hot-water tank. The boiler heats water for the radiators, in-floor loops or baseboard, and the same hot boiler water circulates through a coil inside an insulated storage tank to heat the home's tap water. The two fluids never mix; the tank stores potable water and the boiler simply keeps it hot.
The naming confusion matters when people research boilers online, because British articles and videos use regular and system to distinguish open-vented from sealed heating systems, neither of which is the everyday vocabulary of a BC homeowner. What a homeowner here actually decides is simpler: heating-only boiler with an indirect tank, or a combi boiler that heats tap water on the fly. This page covers the first option, which is sometimes also described on this site as a heating-only boiler paired with an indirect water heater.
How a system boiler and indirect tank work together
The boiler runs a sealed, pressurized loop of heating water. Most of the time that water goes to the radiators or in-floor system; when the tank's thermostat calls, a valve or the boiler's internal diverter sends boiler water through the tank's heat exchanger instead, and a pump circulates it until the stored water reaches its set temperature. Because the tank stores a large volume of hot water, the boiler does not have to fire at full input while someone showers. It reheats the tank at its own pace, often at a lower input, and can be off entirely while stored hot water is drawn.
The separation of jobs is the arrangement's quiet advantage. A hot-water draw does not interrupt the heating, the way it can on a combi, and the tank's recovery is handled whenever the boiler has spare capacity. The tank itself can be sized for the household rather than the boiler, so a family with a large soaker tub or several bathrooms gets a reserve that an on-demand appliance cannot offer. Some manufacturers even support a direct connection between a condensing boiler and its own indirect tank without a primary loop, as IBC describes for its SL G3 heating-only boilers on its Canadian product page.
The other side of that separation is that both jobs depend on one boiler. If the boiler is down for repair, the tank stops being reheated, so homes that cannot accept any hot-water gap sometimes keep a small separate electric or gas water heater for backup, or choose a combi, which has the same single-point dependency but no tank to protect.
Where it fits in a BC home
The heating-only-with-tank arrangement suits homes and buildings with real simultaneous demand: several bathrooms, a large tub, frequent guests, or commercial-style draw patterns in a residential building. It is also the natural choice when a home already has a storage tank and good plumbing, because replacing an old boiler while keeping a sound indirect or storage tank is often the least disruptive path, provided the tank is in good condition and compatible with the new boiler's controls.
Space is the main physical requirement. The tank stands beside the boiler, so the mechanical room needs floor area for both, plus access around them. Basement mechanical rooms in older Vancouver homes usually have that space, which is one reason the arrangement remains common in detached homes here, while townhouses and condos with no mechanical room to spare gravitate to combis.
Installation realities: piping, controls and permits
An indirect-tank installation is more than a boiler swap. The tank needs its own circulator or a valve arrangement, priority control so the tank and the heating zones do not fight over the boiler, and piping sized for both flows. When the boiler is a condensing unit, the same rules as any condensing installation apply: certified ULC S636 plastic venting, condensate drainage, and a system design that keeps return water cool enough for the boiler to condense. Tank recovery raises the return temperature while it runs, so the controls have to manage that moment without pushing the boiler permanently out of its condensing window.
Permits follow the gas-appliance rules used across this site: a gas permit for the boiler and its gas connection, with Technical Safety BC or the municipality issuing it depending on where the property sits; Burnaby, for example, issues gas and heating permits for single-family and duplex dwellings and points larger gas installations to the provincial authority. Annual servicing of the boiler is recommended by Technical Safety BC for all gas appliances, and the tank has its own small maintenance list, including flushing and checking the temperature-and-pressure protection, that a service visit covers.
Questions to ask a contractor
Ask how the tank will be controlled against the heating zones and what happens to the return-water temperature while the tank recovers, since both affect whether a condensing boiler actually condenses. Ask whether the existing tank can stay, what condition it is in, and how its insulation and controls compare with a current indirect tank. Ask for the tank size in gallons or litres and the recovery time at the boiler's output, and compare that with the household's largest draws.
Ask where the tank and boiler will sit and whether the door, stair and floor can handle moving them in. Ask who obtains the gas permit and, where the city issues one, the heating permit. The consultation service on this site covers exactly this decision, tank versus combi, with the home's real hot-water pattern in front of it, and the instant estimator on this site provides a ballpark range before a formal assessment.
Frequently asked questions
What is the difference between a system boiler and a combi boiler?
A combi makes hot water on demand with no tank and is limited by instantaneous flow. A heating-only boiler with an indirect tank stores hot water, so it can serve large simultaneous draws, but it needs floor space for the tank and reheats it between uses.
Can I keep my existing hot-water tank when I replace the boiler?
Often yes if the tank is in good condition, is an indirect or compatible storage design, and the new boiler's controls can manage it. The contractor should inspect the tank and its piping before promising, since a failing tank defeats the point of a new boiler.
If the boiler breaks down, do I lose hot water too?
Yes, the indirect tank is reheated by the boiler, so a boiler outage stops tank recovery. Homes that cannot accept that gap sometimes keep a small separate water heater as backup, which is one of the trade-offs discussed in a consultation.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- Technical Safety BC — homeowner gas permits · accessed September 7, 2026
- City of Burnaby — residential trade permits · accessed September 7, 2026
- IBC SL 14-115G3 — heating-only boiler page (Canada) · accessed September 7, 2026
Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.