Skip to content
Boilers.caby ROMA Heating & Cooling

Comparison

Camus DynaFlame DFW 5000 vs DFW 6004

Verdict in brief

The DynaFlame DFW 5000 and DFW 6004 are the two largest non-condensing domestic-hot-water sizes in the line: 4,999 against 6,000 MBTU/hr input and 4,249 against 5,100 MBTU/hr output, with 5,093 against 6,076 GPH recovery at a 100°F rise.

Side by side

Published manufacturer figures. Input and output are kept separate; blanks mean the manufacturer did not publish that value.

Comparison of Camus DynaFlame DFW 5000 (Non-Condensing DHW) and Camus DynaFlame DFW 6004 (Non-Condensing DHW)
SpecificationCamus DynaFlame DFW 5000 (Non-Condensing DHW)Camus DynaFlame DFW 6004 (Non-Condensing DHW)
Input, maximum4,999 MBTU/hr6,000 MBTU/hr
Output, maximum4,249 MBTU/hr5,100 MBTU/hr
Thermal efficiency85 %85 %
Turndown ratio3:13:1
Shipping weight1,627 lb1,963 lb
VentingCat. I 16" · Cat. III up to 50 ft 10" · Cat. III up to 100 ft 14" · outdoor 10"Cat. I 16" · Cat. III up to 50 ft 12" · Cat. III up to 100 ft 14" · outdoor 12"
Recovery at 100°F rise5,093 GPH6,076 GPH
CertificationCSA International design certified; ANSI Z21.10 / CSA 4.3CSA International design certified; ANSI Z21.10 / CSA 4.3

What actually separates them

Both models are documented in the non-condensing DHW spec sheet (99-0142 Rev 01) and share the platform: 439 stainless-steel six-pass watertube exchanger at 160 psig, up to 85% thermal efficiency, 3:1 turndown with a minimum 35% firing rate, Category I/III venting, and CSA certification to ANSI Z21.10 / CSA 4.3 for domestic hot water.

The printed ratings scale directly. The DFW 5000 delivers 4,999 MBTU/hr input, 4,249 MBTU/hr output and 5,093 GPH (19,277 LPH) at a 100°F rise with a 1,627 lb shipping weight; the DFW 6004 delivers 6,000 MBTU/hr input, 5,100 MBTU/hr output and 6,076 GPH (22,998 LPH) at 100°F with a 1,963 lb shipping weight. The 6004 also steps the printed Cat. III vent diameter to 12" (Cat. I 16") against 10" / 16" on the 5000.

For a large domestic-hot-water plant the choice is the calculated recovery load — the 5000 covers most large institutional loads, and the 6004 is the top printed size when the load requires it. Camus is a Mississauga, Ontario manufacturer; sizing and any storage-tank design belong with a licensed contractor.

Frequently asked questions

How much hot water does the DFW 6004 recover?

The official spec sheet prints 6,076 GPH (22,998 LPH) at a 100°F rise, against 5,093 GPH (19,277 LPH) on the DFW 5000.

Are these boilers condensing?

No. Both are non-condensing DynaFlame DHW models rated up to 85% thermal efficiency with Category I/III venting.

What is the largest DynaFlame DHW size?

The DFW 6004 at 6,000 MBTU/hr input is the largest size printed in the non-condensing DHW spec sheet 99-0142 Rev 01.

Not sure which one fits your home?

A consultation includes a heat-loss review so the size is right the first time.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate