Skip to content
Boilers.caby ROMA Heating & Cooling

Component

DHW flow sensor

On a combi boiler, the DHW flow sensor is the component that notices a hot-water tap has been opened and tells the boiler to switch from space heating to domestic hot water. Without a valid flow signal the burner never starts for hot water, and the tap runs cold. This page explains what the sensor does, how it fails, and what a licensed technician checks.

What it does in a combi system

A combi boiler makes hot water on demand, and the trigger is flow. Navien's NFC-H installation manual describes the logic: the boiler recognizes a DHW demand when the flow sensor detects a DHW flow of approximately 0.5 gallons per minute or greater, and once it detects the flow the boiler immediately goes into DHW mode regardless of the status of the space heating system. That instant switch is the whole point of a combi — no tank, no waiting for a cylinder to recover.

The sensor's other job is measurement, not just detection. Navien's NCB-H service manual describes the flow sensor as detecting water flow in gallons per minute for steady hot water temperatures, which means the control uses the flow rate to modulate the burner and hold a stable outlet temperature as taps open and close.

On the heating side of a combi, a flow sensor also protects the boiler. IBC's DC Series manual includes a no-flow error for a DHW tank or loop where the control enables a pump but sees no flow, and its fixes start with checking the pump and bleeding the loop before moving on to a blocked flow sensor or flow restrictor.

How it fails

The DHW flow sensor is a wet component, and scale is its main enemy. Hard water leaves mineral deposits on the sensor's moving parts and screens until it can no longer spin or register flow properly, and debris from the water supply can block it the same way. Navien's service manual lists the failure events directly: unable to detect or measure water flow rate, and damage to or water leakage from the flow sensor. Its effects are blunt — the ignition sequence does not start, and the boiler stops operating once leakage is detected.

The filter and flow limiter in front of the sensor matter as much as the sensor itself. Viessmann's Vitodens 100-W service instructions for the combi models direct the technician to remove the DHW flow sensor, check the flow limiter and filter sieve, and replace them in case of excessive scaling or damage. A clogged screen starves the sensor of flow and produces the same cold-water complaint as a failed sensor.

Wiring and connector faults also stop the signal. A loose plug or corroded pin can make the sensor intermittent, so the boiler delivers hot water most of the time and then fails during one shower. The error code points at the circuit — Navien lists E439 for an abnormal flow sensor — but the cause can be anywhere between the sensor and the board.

Safe things to check

Confirm the complaint precisely: does the boiler fail to fire for hot water at all, or does the temperature fluctuate? Does a different tap behave differently? A single fixture with low flow can fall below the boiler's demand threshold, while a whole-house failure points at the sensor, the filter or the signal.

The one homeowner task the manuals support is the inlet filter. Navien's NCB-H installation manual instructs the installer to clean the cold water inlet filter after installation and to tell the owner that the filter must be cleaned periodically to maintain proper DHW flow. Beyond that, do not open the water section of a combi boiler — it holds domestic water under pressure, and the sensor sits behind sealed connections.

What a licensed technician will check

A technician tests the flow sensor as an electrical device and as a hydraulic one. Navien's service procedure includes a visual check of the wiring and the sensor for damage or scale, and a voltage check at the sensor's connector while flow is present. Where the sensor is scaled or damaged, it is replaced; where the filter or flow limiter is blocked, it is cleaned or replaced, and Viessmann's procedure installs the sensor with new gaskets and a specified torque on the union nuts.

The technician also confirms the boiler's DHW demand threshold and checks that the water adjustment valve and mixing components are responding — a flow signal alone is not enough if the valve that proportions hot and cold water is stuck. After the repair, they run hot water at several fixtures and verify stable outlet temperatures.

A combi that will not fire for hot water is a classic flow-sensor call, but the filter and limiter are checked first because they cost less and fail more often. If your hot water has gone cold or unstable, call ROMA Heating & Cooling.

Frequently asked questions

My combi heats the house but gives no hot water. Is it the flow sensor?

It is a leading suspect. Navien's manual says the boiler recognizes a DHW demand from the flow sensor's signal, and its service manual notes that a failed sensor stops the ignition sequence for hot water. A technician checks the sensor, its filter and its wiring before replacing anything.

Why does my hot water temperature fluctuate when I shower?

Flow-related causes are common: a scaled flow sensor or a blocked filter or flow limiter changes the flow signal the boiler uses to hold temperature. Viessmann's combi service procedure checks the flow limiter and filter sieve alongside the sensor, and replaces scaled parts.

Can I clean the combi's inlet filter myself?

Navien's manual tells the owner the filter must be cleaned periodically to maintain proper DHW flow, and the installer cleans it after installation. Ask your service technician to show you whether your model's filter is owner-serviceable, because on many combis it sits behind the sealed water section.

Book a consultation

A technician reviews your building and options. Requests are confirmed by ROMA.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate