Component
Diverting valve / combi diverter
The diverting valve — a three-way valve on a combi boiler — steers the boiler's heat between the heating system and the domestic hot water circuit. When it sticks or its actuator fails, a combi can run the radiators while you shower or leave the tap cold while the house heats. This page explains what the valve does, how it fails, and what a licensed technician checks.
What it does in a combi system
A combi boiler has one heat source and two jobs, and the diverting valve decides which job gets the heat. Navien's NCB-H service manual describes the three-way valve's function plainly: it diverts the water from the space heating system to the DHW plate heat exchanger and back, based on input from the DHW flow sensor and the PCB. When domestic hot water is demanded, the valve moves so the boiler's hot water heats the DHW plate exchanger; when the demand ends, it returns the boiler to the heating loop.
The valve also enforces priority. While domestic hot water is being made, space heating is paused, which is why a combi can keep a shower hot in the middle of winter. Viessmann's Vitodens 100-W service instructions refer to the same part as the three-way diverter valve and list its position — heating operation — among the control's target states; during the boiler's purging mode, the pump cycles and the diverting valve moves as part of the sequence.
Because it is a moving part in the water circuit, the valve is one of the components a technician checks whenever a combi has a hot-water or heating complaint that does not fit the sensors.
How it fails
Diverting valves fail mechanically and electrically. The actuator — a small motor or solenoid that moves the valve — can burn out or lose its signal, leaving the valve stuck in whichever position it last held. The valve body can seize from scale and debris, or its internal seals can wear until it bypasses instead of sealing. Navien's service manual lists the failure events as no DHW in space heating mode and no space heating in DHW mode, with error code E016 associated, and its diagnostic is a visual check of the valve's connection wire followed by a voltage check at the actuator.
The symptoms follow the stuck position. A valve stuck on heating leaves the tap cold or lukewarm while the radiators work normally. A valve stuck on DHW can leave the house without heat while the boiler keeps making hot water, or produce warm radiators whenever a tap runs. A valve that is leaking internally can blend the two circuits, producing temperature swings that are hard to pin on anything else.
Viessmann's fault guidance for its combi models includes a check of the three-way diverter valve function in the actuator test whenever heat transfer is poor, which is the same logic from another manufacturer: before blaming the plate heat exchanger or the pump, confirm the valve is actually moving to the position it was told to.
Safe things to check
Observe the pattern. Run hot water and feel whether the heating pipes stay hot or the radiators warm up while the tap is running; then turn the tap off and see whether the house recovers. A boiler that heats the house well but never delivers hot water, or the reverse, points at the valve or its actuator rather than the heat exchanger.
Do not force the valve, and do not remove its actuator. The actuator sits on the water section, and on a hot, pressurized system removing it can release water. Note the error code and the exact behaviour — the technician uses that pattern to decide whether the fault is the motor, the valve body or the signal from the board.
What a licensed technician will check
A technician tests the valve's command and its response. On Navien's NCB-H, the service procedure checks the actuator's connection and measures voltage at the valve while the unit switches modes — the manual lists the expected supply and notes that a valve which has power but does not move is defective. On Viessmann's platform, the diverter valve is exercised through the control's actuator test to confirm it travels through its positions.
Where the actuator has failed, it can often be replaced on its own; where the valve body is scaled or worn, the valve is replaced and the water circuit cleaned. The technician will also check the DHW plate heat exchanger and the flow sensor, because a scaled exchanger or a weak flow signal can mimic a valve fault, and the three parts work as one system.
After the repair, the technician verifies the boiler switches cleanly between heating and DHW with no cross-flow, and that the domestic water reaches its set temperature. If your combi will not do one of its two jobs, call ROMA Heating & Cooling.
Frequently asked questions
My radiators heat up while I run hot water. Is the diverting valve stuck?
That pattern is consistent with a valve that is not fully diverting, but a technician confirms it by testing the actuator and the signal from the board. Navien's service procedure checks the valve's connection and voltage, and Viessmann's platform exercises the valve in an actuator test.
My combi makes hot water but the house stays cold. Could it be the diverter?
Yes. Navien's manual lists no space heating in DHW mode as a failure event for the three-way valve. A technician checks the valve alongside the pump, the zone controls and the sensors, because a stuck valve and a weak pump can produce similar complaints.
Can the diverting valve be repaired, or does it get replaced?
It depends on the failure. A failed actuator can often be replaced on its own, while a scaled or worn valve body is replaced and the water circuit cleaned. Either way the technician verifies the boiler switches cleanly between heating and hot water afterwards.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- Navien NCB-H Service Manual · 1.00 (Feb 2021) · accessed September 9, 2026
- Viessmann Vitodens 100-W B1HE/B1KE Installation and Service Instructions · 6167 818 - 22 · accessed September 9, 2026
- Navien NCB-H Installation and Operation Manual · accessed September 9, 2026
- FortisBC — Appliance maintenance and safety · accessed September 9, 2026
Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.