Component
Expansion tank
An expansion tank gives heating water somewhere safe to go as it heats and grows, keeping pressure stable and protecting the relief valve. This page explains how the tank works, how a lost air charge or failed diaphragm shows up, and what a licensed technician checks before replacing it.
What it does in a hydronic system
Water does not compress, but it does expand when heated. In a sealed hydronic system, that expansion would drive pressure steadily upward every time the boiler fires. The expansion tank provides a cushion of air — separated from the water by a rubber diaphragm or bladder in modern tanks — that compresses as the water grows, so pressure rises gently instead of spiking.
The tank is connected to the boiler piping, and IBC's SL G3 manual directs installers to place the expansion tank connection on the suction side of the circulator with minimal piping between them, a position that keeps pump operation stable. On the wall-hung condensing boilers common across Greater Vancouver, a small diaphragm tank usually hangs beside or above the boiler.
The tank works together with two other components: the pressure-reducing fill valve that tops the system up to its cold-fill pressure, and the pressure relief valve, which should never have to open during normal operation. A correctly functioning tank is the reason the gauge needle barely moves from cold to operating temperature.
How it fails
Expansion tanks fail in two main ways. The air side can slowly lose its charge through the valve or a corroded fitting, leaving the tank waterlogged — full of water with no cushion left. Or the diaphragm can rupture, which does the same thing in one event: water floods the air side and the tank becomes a dead piece of pipe.
When the cushion is gone, the symptom is unmistakable: the pressure gauge climbs hard as the boiler heats up, and a boiler that ran at a steady pressure starts spiking toward the relief valve's setting every cycle. The relief valve may then weep small amounts of water — a classic sign that points at the expansion tank, not the relief valve. Less dramatic failures include a wrongly pre-charged or undersized tank, which causes pressure to swing wider than it should between heating cycles.
IBC's SL G3 servicing checklist tells the technician that boiler pressure should stay stable while the boiler fires and the water temperature rises, and that a sharp rise is a reason to consider replacing the expansion tank.
Safe things to check
The gauge is your best window into the expansion tank. Note the pressure when the system is cold, then watch it while the boiler runs and the water warms. A healthy system moves only a small amount; a needle that climbs steeply or pushes past the normal zone points at a lost air charge or a failed diaphragm.
Also look for drips. Water on the floor under the relief valve's discharge pipe, or a valve that is constantly wet, is often the expansion tank's failure announcing itself through the relief valve. Leave the tank's air valve alone — it is not a tire valve for topping up, and pressing it on a waterlogged tank releases hot water under pressure.
What a licensed technician will check
A technician confirms the diagnosis by measuring both sides of the system. They check the cold-fill pressure on the boiler gauge, then isolate the tank and check the air-side charge with a pressure gauge against the value specified for the system, which tells them whether air has leaked out or the diaphragm has failed.
Where the charge is simply low, the tank can be re-pressurized with dry air; where the diaphragm has ruptured or corrosion has set in, the tank is replaced. The technician will also confirm that the replacement is sized for the system's water volume, verify that the fill valve is closing properly, and re-check that pressure stays steady while the boiler fires.
Because a failing tank is the most common cause of a weeping relief valve, technicians treat the two as one job: fix the tank, then confirm the relief valve no longer discharges. If your boiler's pressure climbs every time it heats, call ROMA Heating & Cooling rather than letting the relief valve do the tank's job.
Frequently asked questions
Why is water dripping from my boiler's relief valve?
Most often it is not the relief valve at all but a waterlogged or under-charged expansion tank that lets pressure climb too high each cycle. The fix is to restore or replace the tank, then confirm the relief valve reseats properly.
Can I just add air to my expansion tank myself?
Adding air is only correct on a tank whose water side has been isolated and drained down, and the right charge depends on the system's fill pressure. Doing it wrong can push water past the fill valve or leave the tank useless. A technician will measure both sides and set it correctly.
Is a rising pressure gauge an emergency?
Not on its own, but do not ignore it. If the relief valve begins discharging continuously, or the pressure keeps climbing, turn the system down and call a technician, because a relief valve that has lifted may not reseat cleanly.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- IBC SL 10-85 G3 / SL 14-115 G3 / SL 20-160 G3 / SL 30-199 G3 Installation & Operating Manual · 120-276E13 · accessed September 7, 2026
- FortisBC — Appliance maintenance and safety · accessed September 7, 2026
- Technical Safety BC — homeowner gas permits · accessed September 7, 2026
Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.