Component
Flame sensor (flame rod)
The flame sensor is the small rod that proves a gas boiler's burner is actually lit before the control will keep the gas valve open. This page explains flame sensing, the faults that shut a boiler down, and what a licensed technician checks — gas-system work stays with licensed contractors.
If you smell gas
- Stop what you are doing. Do not use phones, switches, matches or anything that can spark inside.
- Go outside and leave the door open behind you.
- Call the FortisBC 24-hour emergency line at 1-800-663-9911 or dial 911.
Only after that, call ROMA about the boiler. Official guidance: FortisBC gas leaks and odour.
Safety first
If you smell gas, leave the building and call FortisBC at 1-800-663-9911 or 911 from outside before anything else. A rotten-egg smell is a gas emergency regardless of what the boiler display says: stop what you are doing, get outside first, and call the FortisBC emergency line at 1-800-663-9911 or 911 from there. Do not switch lights, do not reset the boiler, and do not investigate.
A boiler that fails to prove flame is not itself a gas leak — it is the safety system refusing to let gas flow — but flame detection lives on the gas side of the appliance, and work there is reserved for licensed gas contractors under Technical Safety BC. The homeowner's job is to notice, report, and stay clear.
What it does in a hydronic system
A gas boiler must never keep its gas valve open without proof that the burner is burning. The flame sensor — a small rod positioned in the flame, sometimes called a flame rod — provides that proof through flame rectification: the flame conducts a tiny electrical current between the rod and the burner, and the control measures that current as the signature of a live flame. When the signal is present the gas valve stays open; when it disappears the control closes the valve in well under a second. IBC's SL G3 ignition timing table lists a flame failure response time under 0.8 second, and its troubleshooting section treats a flame-current drop as a fault with named minimums: 1.4 µA for the SL 10-85 G3 and SL 14-115 G3, 1.8 µA for the SL 20-160 G3, and 3.2 µA for the SL 30-199 G3.
On the SL G3 the same control family also watches the vent: the manual's flame signal error can be flagged alongside vent blockage, since a blocked vent changes combustion and the flame's behaviour. Flame sensing is thus both a combustion control and a safety device, which is why the sensor, its lead and its ground are checked as a system rather than as a disposable part.
How it fails
A flame sensor fails from the environment it lives in: heat, soot and condensation. A coating of soot or moisture on the rod insulates it from the flame and weakens the signal; the ceramic insulator can crack and leak current to ground; and the grounding path between the burner and the control can degrade, which weakens the measured signal even with a clean rod. Wiring and connector corrosion are common accomplices.
The boiler's behaviour tells the story. A flame signal that drops below the model's minimum makes the control shut the burner down — the boiler fires, then stops, then retries, often logging an ignition or flame failure and locking out after repeated attempts. On the SL G3, the troubleshooting path for a flame-signal error walks the technician through vent blockage, gas pressure, combustion settings, and the condition and grounding of the flame rod before any part is replaced.
Safe things to check
If you smell gas, the first section applies and nothing else matters. If there is no smell, the safe job is reading the boiler display and writing down the exact alert text — a flame or ignition error tells the technician which system to test before they arrive. Notice whether the boiler fires and then stops, or never attempts to light, and how often it retries; that pattern is diagnostic information.
Never open the boiler to look at, clean or reposition the flame sensor, and never touch the ignition area. The flame rod sits beside the burner where high voltage and gas meet during ignition, and that combination is exactly the territory the licensed-gas-work rules reserve for contractors.
What a licensed technician will check
A technician approaches a flame fault by measuring, not guessing. On the SL G3 the manual guides them to confirm the vent is clear, the gas pressure is within range, and the combustion readings are stable, then to inspect the flame rod's condition, its grounding, and its wiring — checking that the probe is electrically isolated from the vessel and that the ceramic insulator is intact. Flame current is compared against the model's minimum, and a rod that cannot deliver it is cleaned or replaced.
After any repair the technician verifies the boiler lights reliably and holds flame across several trials, and checks combustion with an analyser before leaving. If your boiler fires and drops out repeatedly, or displays a flame error, call ROMA Heating & Cooling — most flame faults end in a cleaned or replaced rod, not a boiler.
Frequently asked questions
My boiler lights and then shuts off after a few seconds. Is that the flame sensor?
It is one of the first things a technician checks: a weak flame signal makes the control close the gas valve almost immediately — IBC's SL G3 responds to flame failure in under 0.8 seconds. Vent blockage, gas pressure and the rod's condition and grounding are tested before parts are replaced.
What is flame rectification?
It is the electrical principle behind flame sensing. A flame conducts a small current in only one direction between the sensor rod and the burner, and the control reads that rectified current as proof the burner is lit. No flame, no signal, gas valve closed.
Can I clean the flame sensor myself to save a service call?
No. The sensor sits in the burner area of the gas train, and cleaning or handling it means opening the boiler where gas and ignition components live. This is licensed-gas-contractor work in BC, and the diagnosis usually involves more than wiping the rod anyway.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- FortisBC — Gas leaks and odour (natural gas safety) · accessed September 8, 2026
- IBC SL 10-85 G3 / SL 14-115 G3 / SL 20-160 G3 / SL 30-199 G3 Installation & Operating Manual · 120-276E13 · accessed September 8, 2026
- Technical Safety BC — homeowner gas permits · accessed September 8, 2026
Facts checked September 8, 2026. Last updated September 8, 2026. Technical reviewer: not yet assigned.