Skip to content
Boilers.caby ROMA Heating & Cooling

Component

Flue temperature sensor

The flue temperature sensor — sometimes called the stack or exhaust sensor — measures how hot the gases leaving the boiler are. It protects the venting and the heat exchanger by turning a dirty, blocked or overheating condition into a shutdown before damage occurs. This page explains what the sensor does, how it fails, and what a licensed technician checks.

Safety first

If you smell gas, leave the building and call FortisBC at 1-800-663-9911 or 911 from outside before anything else. If a carbon-monoxide alarm sounds, leave the building and call 911 from outside — CO is odourless and invisible, so alarms, not senses, are the warning. Do not go back inside to investigate until the building has been checked.

The flue temperature sensor is one of the devices that keeps a boiler from venting abnormal combustion products, so faults in this circuit are treated as safety faults. The sensor itself does not carry gas, but it sits in the combustion path, and work on it follows the same licensed-gas-contractor rules as the rest of the appliance.

What it does in a hydronic system

A condensing boiler extracts so much heat from its flue gases that they leave cool and wet, which is why plastic venting is allowed. The flue temperature sensor watches that balance. If the flue gases get too hot, something is wrong — the heat exchanger may be scaled, the water flow may be too low, or the vent may be restricted — and the control uses the sensor's reading to protect the appliance and the vent.

IBC's SL G3 troubleshooting guide documents the protection threshold: a Vent High Limit error is raised when exhaust gas temperature exceeds 248 °F for 6 seconds, or 232 °F for 60 seconds, and the boiler goes into a hard lockout. The fix starts with checking return water temperature, because a boiler that is not condensing properly sends heat up the flue instead of into the water.

NTI's TFT manual shows the same logic with a Canadian-specific detail: Lockout 82 — Stack limit protects the vent, and unless the boiler is installed in Canada with PVC exhaust venting, the stack limit setpoint is set to its maximum of 220 °F; in Canada, PVC exhaust venting is limited to 149 °F. Navien's controls use an exhaust thermistor and a separate exhaust limit temperature sensor, with E047 raised for an exhaust thermistor fault.

How it fails

Flue sensors fail from the environment they live in. Heat, moisture and the acidic condensate in the flue path can corrode a probe or its wiring until the circuit goes open or short — the failure modes the error tables list. Connectors loosen or corrode, and a sensor that has been disturbed during service can be left partially out of position, reading the flue wall instead of the gas stream.

The failures that matter most are not the sensor at all. A dirty heat exchanger, scale build-up or restricted water flow makes the flue genuinely too hot, and the sensor is doing its job when it shuts the boiler down. NTI's manual connects the stack-limit fault to a dirty heat exchanger and notes that if the error is accompanied by popping or hissing, the boiler may have scale preventing proper heat transfer. A blocked condensate line or vent can cause the same protective shutdown.

The symptoms are usually an error and a lockout rather than a subtle change: the boiler heats, then stops with a flue or stack error, and may not restart until conditions return to normal. IBC's control requires the temperature to fall before the error clears, and NTI's manual-reset stack fault works the same way.

Safe things to check

Write down the exact error text. IBC's touchscreen scrolls through active alarms and colour-codes them — green, yellow, red — so note the colour as well as the words. Keep the outdoor vent terminals clear of snow, leaves and debris, since a restricted vent is one of the conditions the sensor protects against.

Do not reset a boiler repeatedly when it is raising a flue or vent error, and do not open the boiler to look at the sensor. A flue over-temperature condition means the appliance is telling you something needs attention — scale, flow, venting or the sensor itself — and each of those requires a technician with the right instruments.

What a licensed technician will check

A technician starts by asking why the flue got hot. IBC's guide directs a check of return water temperature; NTI's manual sends the technician to inspect and clean the heat exchanger, check water flow and pressure, check for scale, and verify the venting and condensate drainage. Combustion and temperature readings are taken with instruments rather than guessed at.

The sensor circuit is tested directly. NTI's procedure for a stack sensor fault has the technician check the sensor connection at the flue pipe inside the boiler cabinet and at the control board, then measure the sensor's resistance against the manual's thermistor table. NTI's annual checklist also inspects the flue sensor grommet seal and test port plug for leakage or signs of failure, replacing them when damaged, because the sensor passes through the boiler's combustion boundary. Where the sensor is faulty it is replaced; where the heat exchanger or venting is the cause, that is addressed first.

After the repair, the technician verifies the boiler runs through a full cycle without tripping the limit and confirms combustion with an analyser. If your boiler is locking out on a flue or stack error, call ROMA Heating & Cooling.

Frequently asked questions

Why does my boiler lock out with a flue or stack error?

The flue is hotter than the boiler's limit allows. IBC's control trips above 248 °F for 6 seconds or 232 °F for 60 seconds, and NTI's stack limit protects the vent. Causes range from a scaled heat exchanger and low water flow to a blocked vent — or a faulty sensor — so a technician diagnoses the reason rather than resetting it away.

Is a flue sensor fault dangerous?

It is treated as a safety circuit, because the sensor is part of what keeps the boiler from venting abnormal combustion products. The boiler is designed to lock out rather than run in that condition, and if a CO alarm sounds, leave the building and call 911 from outside.

Can I keep resetting the boiler when the flue error appears?

No. A flue over-temperature condition means something needs attention — scale, water flow, venting or the sensor — and repeated resets can hide the pattern and delay the repair. Note the error text and call for service.

Book a consultation

A technician reviews your building and options. Requests are confirmed by ROMA.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate