Skip to content
Boilers.caby ROMA Heating & Cooling

Component

Ignition cable

The ignition cable carries the high-voltage spark from the boiler's ignition module or transformer to the electrode at the burner. A cable that is loose, cracked, wet or contaminated can stop a boiler from lighting, and because it works next to the gas train, all checks and repairs belong to a licensed technician. This page explains the cable's job, how ignition faults develop, and what a technician tests.

Safety first

If you smell gas, leave the building and call FortisBC at 1-800-663-9911 or 911 from outside before anything else. A rotten-egg smell is a gas emergency: stop what you are doing, get outside first, and call from there. Do not reset the boiler, do not touch switches, and do not investigate.

The ignition cable is part of the system that lights the burner, so it sits on the gas side of the appliance. In British Columbia, work on ignition components is gas-contractor work under Technical Safety BC rules, and the boiler manuals treat it that way — IBC's SL G3 troubleshooting guide has technicians check the ignition lead's security and condition rather than inviting anyone else near it.

What it does in a hydronic system

A boiler lights its burner with a spark, and the ignition cable is the wire that delivers it. The control energizes the ignition module or transformer, which produces a high-voltage pulse; the cable carries that pulse to the electrode, where it arcs across a small gap to the burner and ignites the gas-air mixture. Because the voltage is high, the cable is insulated and routed carefully — a path for the spark that keeps it away from anything it should not touch.

The cable's condition is part of the ignition system's reliability. IBC's SL G3 troubleshooting guide lists a noisy spark when igniting as a symptom of an ignition lead that is not firmly connected, with a simple fix: reconnect the ignition lead. The same guide directs the technician to check that the ignition lead is secure at the control module and at the probe as the first step when ignition trials are exceeded.

On IBC's DC Series, the manual goes further: a poor flame signal has the technician check the ignitor and ignition cable, and a flame-detection fault lists replacing the ignition cable and ignitor cap as a fix. NTI's FTG manual gives the same instruction from the installer's side: if the spark cable is disconnected, ensure the high-voltage spark cable is securely connected to the spark generator and the igniter.

How it fails

Ignition cables live in a hostile place — heat, moisture from the combustion process, and vibration from the fan. The common failures are connection faults and insulation faults. A terminal that has loosened at the module or the electrode weakens or interrupts the spark; cracked or carbon-tracked insulation lets the high voltage arc to the boiler chassis instead of the burner; and moisture or combustion contaminants on the probe end can deaden the spark or the flame signal.

The boiler's behaviour tells the story. A boiler that sparks but does not light, or one that lights and then shuts off at the end of the ignition trial, points at the ignition and flame-proving circuits — IBC's guide ties an improperly grounded burner, an unserviceable ignition lead or a failing spark module to exactly that pattern. Repeated failures produce an ignition lockout: IBC's control locks out for an hour after three failed tries, then repeats the sequence, and the display text tells the technician where to start.

The cable is not usually the only suspect. IBC's ignition-issues table also lists contaminants or moisture on the ignitor probe, fluctuating gas pressure and gas piping problems, which is why the diagnosis follows a sequence rather than a hunch.

Safe things to check

If you smell gas, the first section applies and nothing else matters. If there is no smell, the safe job is reading the display: note the exact ignition or flame error and whether the boiler sparks at all, because a no-spark condition and a spark-but-no-light condition send a technician down different paths.

Never open the boiler to look at the ignition cable, and never reach into the burner area to dry or adjust anything. The ignition circuit carries high voltage beside raw gas during a trial for ignition, and that combination is precisely what the licensed-gas-work rules exist for.

What a licensed technician will check

A technician verifies the ignition circuit from end to end. Following IBC's SL G3 procedure, they confirm the ignition lead is secure at the control module and at the probe, check the probe gap against the manual's specification — IBC specifies a gap between 1/8 and 3/16 inch (3.2 to 4.7 mm) — and confirm the probe is electrically isolated from the vessel with its ceramic insulator intact. Navien's NCB-H service manual lists its igniter gap as 3.5 to 4.5 mm and has the technician check the ignition transformer's output when no spark is present.

Where the cable has failed — cracked insulation, a damaged terminal or contamination that cannot be cleaned — it is replaced, along with the ignitor cap or probe when the manuals call for it. The technician then verifies the burner lights reliably across several trials and confirms combustion with an analyser before leaving.

Ignition faults are among the most common no-heat calls, and most end with a probe, a cable or a module rather than a boiler. If your boiler is locking out on ignition, call ROMA Heating & Cooling.

Frequently asked questions

My boiler clicks but does not light. Is the ignition cable the problem?

It can be, but so can the probe, its gap, the grounding path or the gas supply. IBC's guide starts by checking that the ignition lead is secure at the control module and at the probe, then checks the probe gap and isolation before any part is replaced.

Why does my boiler make a loud snapping or buzzing at ignition?

IBC's troubleshooting guide calls this a noisy spark and ties it to an ignition lead that is not firmly connected. It is worth a prompt service call, because the spark is arcing where it should not and ignition may fail next.

Can I dry or clean the ignition parts myself?

No. The ignition circuit carries high voltage beside raw gas during a trial for ignition, and in BC that work belongs to licensed gas contractors. IBC's guide treats probe contamination as a technician's service item, not a homeowner task.

Book a consultation

A technician reviews your building and options. Requests are confirmed by ROMA.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate