Skip to content
Boilers.caby ROMA Heating & Cooling

Component

Ignition electrode

The ignition electrode creates the spark that lights the burner in a gas boiler, and on many models it also senses the flame once it is burning. This page explains the part, how ignition faults develop, and what a licensed technician checks before repairing the ignition system.

Safety first

If you smell gas, leave the building and call FortisBC at 1-800-663-9911 or 911 from outside before anything else. FortisBC's guidance is unambiguous: a rotten-egg smell means stop what you are doing, get outside first, and call the emergency line or 911 from there. Do not switch lights, do not reset the boiler, do not investigate — just leave and call.

A gas boiler that fails to light is not itself a gas leak, but ignition faults are gas-system faults, and in British Columbia work on them is reserved for licensed gas contractors under Technical Safety BC. Your part is to notice, report and stay clear.

What it does in a hydronic system

Before a boiler can make heat it must light its burner safely, and that is the ignition electrode's job. The control sends high voltage to the electrode, which arcs across a small gap to the burner or ground, igniting the gas-air mixture. On many condensing boilers the same probe, or a partner flame sensor, then uses flame rectification — a tiny electrical signal that only a flame conducts — to prove the burner is actually lit before the gas valve is allowed to stay open.

IBC's SL G3 uses direct spark automatic ignition, and its troubleshooting tables treat the electrode, its lead and the spark module as one system: an ignition failure can come from any of them, which is why technicians test rather than guess.

How it fails

Ignition parts fail from heat, moisture and wear. The ceramic insulator around the electrode can crack, letting the spark arc to ground instead of across the gap. The gap itself can close up or open out of spec, the ignition lead can break down and arc against the boiler chassis, and soot or moisture on the probe can deaden the spark or the flame signal.

The boiler's behaviour tells the story. A boiler that tries to light and fails repeatedly will, on IBC's V-10 control, log an ignition trials error after three failed attempts and lock out — the SL G3 manual describes a one-hour lockout followed by another three-try sequence. The display text matters: a spark that is firing but not lighting points at gas supply, while a boiler that never sparks points at the electrode, lead or spark module.

Safe things to check

If you smell gas, the first section applies and nothing else matters. If there is no smell, the safe job is reading the boiler display and noting the alert text so a technician can prepare. Reset the boiler once if the manual you keep with the appliance allows it, but if the ignition error returns, stop resetting — repeated resets can hide the pattern and, on some controls, extend the lockout.

Never open the boiler to look at the electrode, and never reach inside to dry or clean a probe. The electrode area is one of the few places in a boiler where the parts carry both high voltage and raw gas, and that combination is exactly what the licensed-gas-work rules exist for.

What a licensed technician will check

A technician approaches an ignition failure methodically. They confirm the gas supply is on and the line was purged of air after any recent work, then verify the control is sending spark. IBC's SL G3 troubleshooting guides the technician through the likely causes: the ignition lead secure at both the control module and the probe, the probe gap set to the manual's specification (the SL G3 manual specifies 1/8 to 3/16 inch, about 3.2 to 4.7 mm), the ceramic insulator intact, and the probe electrically isolated from ground. A lead or spark module that fails its checks is replaced.

After any ignition repair the technician verifies the burner lights reliably across several trials and confirms clean combustion before leaving. If your boiler is locking out on ignition, call ROMA Heating & Cooling — most ignition faults are resolved with a probe, lead or module replacement, not a boiler.

Frequently asked questions

Is an ignition lockout the same as a gas leak?

No. A lockout means the boiler failed to light and shut itself down, which is the safety system working. A gas smell is a different event entirely: leave the building and call FortisBC at 1-800-663-9911 or 911 from outside.

Why does my boiler light sometimes but not others?

Intermittent ignition often points to a marginal gap, a failing lead that arcs when hot, or moisture on the probe. Technicians call this a classic diagnosis-by-testing fault rather than a part-swapping one.

How long do ignition electrodes last?

Many last the life of the boiler, but they are a wear item exposed to flame and condensation. A technician can inspect the insulator and measure the gap during annual servicing and replace the probe before it strands you on a cold morning.

Book a consultation

A technician reviews your building and options. Requests are confirmed by ROMA.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate