Component
Pressure relief valve
The pressure relief valve is a boiler's last line of defence: if system pressure ever exceeds the boiler's rating, the valve opens and discharges water and steam to keep the vessel from failing. This page explains the valve, why it weeps, and what a licensed technician checks.
What it does in a hydronic system
Every hydronic boiler is a sealed pressure vessel, and every sealed pressure vessel needs a controlled way to relieve overpressure. That is the pressure relief valve's job: a spring-loaded valve set to open at the boiler's rated pressure — IBC's SL G3, for example, ships with a 30 psig relief valve — discharging water or steam through an outlet pipe to a safe location whenever pressure exceeds the set point.
The valve is a safety device, not a pressure regulator, and the installation rules treat it that way. IBC's SL G3 manual requires the relief valve to be installed with no valves or other means of isolation between it and the boiler, and its outlet piped unobstructed to a safe discharge point. The protection chain is designed so the relief valve is the last thing to act, after the expansion tank and the controls have failed to keep pressure in check.
On the wall-hung condensing boilers common across Greater Vancouver, the relief valve is a compact brass fitting near the top of the water connections, with a short discharge pipe — and its discharge pipe should never be capped, valued or routed where a hot discharge could injure someone.
How it fails
A weeping relief valve — one that dribbles water intermittently from its discharge pipe — is the most common failure, and it is usually a symptom rather than the disease. When an expansion tank loses its air charge or a fill valve over-pressurizes the system, pressure climbs every heating cycle until the valve lifts slightly, and a valve that has lifted once often never reseats perfectly. The water you see dripping may be the last chapter of an expansion tank story.
Other failures are more serious. A valve can fail open after debris lodges in its seat, discharging continuously — hot water and steam pouring from the pipe, which also means the system keeps losing water and pressure. Or a valve can fail closed, seized by corrosion or scale, so it never opens when pressure actually reaches its set point; that is the failure nobody sees until it matters. Blocked discharge piping turns even a correctly opening valve into a hazard, which is why the pipe is never supposed to be capped or kinked.
Safe things to check
The discharge pipe end is the observable part of the valve. Check occasionally that it is dry and unobstructed: a valve that weeps leaves staining or water at the pipe end, and that is your cue to call. If the valve is discharging a steady stream or steam, keep clear of the discharge point and have the boiler turned down — a continuously discharging valve means the system cannot hold its pressure.
Never cap, plug, tape or extend the discharge pipe yourself, and never hold the valve open to test it or to drain pressure; relief valves are not user-serviceable, and testing them is a technician's job done with the system understood. Do not touch the adjustment on the valve — its set pressure is fixed to match the boiler's rating.
What a licensed technician will check
A technician treats a weeping relief valve as a system diagnosis, not a part swap. They check the boiler's cold pressure against its normal range, verify the expansion tank's air charge and the fill valve's setting, and only then judge the relief valve itself. A valve that lifted once is often replaced rather than trusted to reseat, because reseating is not guaranteed — IBC's SL G3 manual notes that relief valve blow-off may be needed during maintenance, and any servicing that opens the valve should end with it verified.
The technician also confirms the installation rules are met: the correct set pressure for the boiler's rating, no isolation valve between the boiler and the relief valve, and a discharge pipe that is unobstructed and routed to a safe drain. Where the valve is replaced, the job is straightforward for a licensed contractor and the system is refilled and re-verified afterwards.
A relief valve is inexpensive; the boiler it protects is not. If yours is weeping, or you notice pressure climbing on the gauge, call ROMA Heating & Cooling — the fix is usually the expansion tank and a new valve, and it is a routine service call.
Frequently asked questions
Is a dripping relief valve an emergency?
A drip is a warning, not usually an emergency. It tells you the system is regularly reaching relief pressure, which should not happen. Book a technician; if the valve ever discharges a continuous flow of water or steam, turn the system down and treat it as urgent.
Can I test the relief valve by lifting its lever?
Leave that to the technician. Lifting the lever on a system at pressure releases scalding water, and a valve that does not reseat after a test needs replacement anyway. The technician will test or replace it as part of servicing.
Why does my relief valve drip only in winter?
Because that is when the boiler fires most. Each heating cycle expands the water, and if the expansion tank has failed, the pressure climbs to the relief valve's set point every cycle — the winter drip is the tank's failure, announced through the valve.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Related
Sources and verification
- IBC SL 10-85 G3 / SL 14-115 G3 / SL 20-160 G3 / SL 30-199 G3 Installation & Operating Manual · 120-276E13 · accessed September 7, 2026
- FortisBC — Appliance maintenance and safety · accessed September 7, 2026
- Technical Safety BC — homeowner gas permits · accessed September 7, 2026
Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.