Component
Room thermostat
The room thermostat is the switch that tells a heating zone to call for heat, and on a modern boiler it is also part of the control system's wiring. The wrong thermostat type, a miswired connection or a failed wire can produce ghost calls, no-heat complaints and lockouts that look like boiler faults. This page explains what the thermostat does, how it goes wrong, and what a licensed technician checks.
What it does in a hydronic system
A room thermostat closes a low-voltage circuit when a room falls below its setpoint, and the boiler or zone control responds by running the circulator and firing the burner. That much has not changed in decades, but the electrical details matter more now. IBC's DC Series manual states the requirement plainly: the room thermostat must be a dry-contact style thermostat, and its troubleshooting procedure checks the connector terminals for 24 volts DC with the thermostat wires disconnected.
On Navien's NCB-H, the boiler's own board provides the thermostat terminals: if you have a 24-volt thermostat, connect it to the R and C terminals on the boiler's PCB, and the C terminals are for optional connections with 24-volt thermostats that have a common wire. NTI's TFT manual describes the same architecture from the other side: the R terminal can be used with COM to provide a power source for a digital thermostat, and a central heat demand switch connects between R and the CH2 terminal and must be an isolated end switch — a dry contact.
Modern thermostats add schedules, remote sensors and smart features, but they still have to present the right kind of signal to the boiler. A thermostat that steals its power through the heating circuit, or one whose contact is not isolated, can confuse a control that expects a clean switch closure.
How it fails
IBC's SL G3 troubleshooting guide documents one of the classic thermostat faults: a ghost call for heat. A triac or a power-robbing thermostat can send a small current through the thermostat wiring even when the thermostat is not calling, and the boiler interprets it as a demand. The guide's diagnostic is to remove the thermostat connections from the boiler and confirm that stray voltage or induced current is the source, then replace the power-robbing thermostat, isolate the thermostat with a relay or install a properly sized resistor after consulting the thermostat manufacturer.
The guide also covers thermostats that overshoot: an incorrect anticipator setting can let the temperature exceed the thermostat's setting, and on a boiler controlled by the V-10 platform the anticipator should be set to zero. A mercury thermostat that is not level can behave the same way. These are thermostat faults, not boiler faults, but they look like heating problems from the living room.
Wiring and power failures round out the list. A thermostat with dead batteries, a broken conductor in the cable, or a loose terminal at either end produces a zone that never calls. Because thermostats are low-voltage devices, a failed wire is more common than a failed boiler — and it is the first thing a technician checks when one zone is cold while the others work.
Safe things to check
Before assuming a fault, confirm the basics: the thermostat is set above room temperature, its schedule is not holding the zone off, and its batteries are fresh if it uses them. Compare zones — if only one area is cold, the problem is likely that zone's thermostat, wiring or valve rather than the boiler.
Do not rewire a thermostat to a boiler yourself, and do not remove a thermostat from the wall while the heating season is under way unless you can isolate the circuit first. Thermostat wiring is low voltage, but a mistake can leave a zone calling continuously, or leave the boiler unable to fire when you need it.
What a licensed technician will check
A technician verifies the whole control chain: the thermostat's type and operation, the voltage and continuity of the wiring, and the terminals at the boiler or zone panel. On IBC's platform they check for stray voltage with the thermostat disconnected, as the ghost-call procedure describes, and confirm the thermostat is a dry-contact type where the boiler requires one.
Where the thermostat is the problem, it is replaced with a compatible model and configured correctly — including the anticipator setting, which IBC directs to zero on its V-10 platform. The technician then confirms the boiler fires only when the thermostat actually calls, and shuts down cleanly when the call ends.
Thermostat complaints are among the most common no-heat calls, and most end with a wiring repair, a configuration fix or a new thermostat rather than a boiler repair. If a zone will not heat or will not stop heating, call ROMA Heating & Cooling.
Frequently asked questions
My boiler fires even though the thermostat is not calling. Why?
IBC's SL G3 guide calls this a ghost call for heat: a triac or power-robbing thermostat sends stray current through the wiring and the boiler reads it as a demand. The fix is to confirm the stray voltage, then replace or isolate the thermostat as IBC describes.
Which thermostat type does my boiler need?
Many modern controls expect a dry-contact signal, and IBC's DC Series manual states the room thermostat must be a dry-contact style thermostat. Navien's NCB-H supports 24-volt thermostats on its R and C terminals. A technician confirms compatibility before a thermostat is replaced.
Why does my house overshoot the thermostat setting?
An incorrect anticipator setting is a common cause — IBC's guide directs setting the anticipator to zero on its V-10 platform — and a mercury thermostat that is not level can do the same. A technician checks the thermostat's configuration as part of the diagnosis.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- IBC DC Series Boilers / Water Heaters Installation and Operating Instructions — DC 15-95, DC 15-96, DC 20-125, DC 33-160 · 120-183-A-R11 · accessed September 9, 2026
- IBC SL 26-260 G3 / SL 40-399 G3 Commercial Installation & Operating Manual (V-10 controller) · 120-270E12 · accessed September 9, 2026
- Navien NCB-H Installation and Operation Manual · accessed September 9, 2026
- NTI Trinity Tft 60-399 Installation and Operation Instructions · 99984535 · accessed September 9, 2026
Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.