Component
System feeder / auto fill valve
A system feeder, also called an automatic fill valve, keeps a hydronic system topped up by admitting make-up water through a pressure-reducing valve. This page explains how a feeder works, why a feeder that never stops feeding is a warning sign, and what a technician checks.
What it does in a hydronic system
A sealed hydronic system should not need water very often. When it does — after servicing, or because of a small loss — the system feeder admits water from the household supply and reduces the pressure to the level the system needs. IBC's SL G3 manual describes the usual arrangement: fluid fill is most often accomplished with a boiler regulator and fill valve set at 12 psig or higher, together with a backflow prevention device as required by local code. Laars' Mini-Therm manual is equally direct, stating that a pressure reducing valve (automatic feed) must be used to maintain the system at constant proper pressure.
A feeder is more than a tap. It includes a pressure-reducing valve that holds the downstream side at a set fill pressure, a check or backflow preventer so heating water cannot flow back into the domestic supply, and usually a shutoff or bypass so a technician can isolate it. Some modern boilers do the job themselves: Navien's NCB-H automatically replenishes water when its pressure sensor detects an insufficient level, and displays E351 if the replenishment is not completed within five minutes.
The feeder works with the expansion tank and the pressure gauge. Together they keep a cold system at its fill pressure and let pressure rise only slightly as the water heats.
How it fails
Feeders fail at the valve seat. Debris from the water supply can keep the seat from closing, so the feeder keeps adding water and system pressure climbs every time the boiler runs. The pressure gauge then pushes toward the relief valve setting, and the relief valve starts weeping — a symptom homeowners often blame on the relief valve itself. The opposite failure is a feeder that will not open, so the system slowly loses pressure until the boiler locks out on low water or low pressure.
There is also a failure of habit. NTI's Trinity TFT manual warns that automatic feed valves should not be left open indefinitely, because in the event of a leak the feeder will keep supplying fresh, untreated water; fresh water contains oxygen and minerals that can lead to scaling and corrosion of the heat exchanger. A feeder that is quietly topping up a leaking system is masking a problem, not solving one. Navien's service manual, similarly, directs a technician who finds water is not being refilled to check the auto feeder valve filter and, if power is present and the filter is clear, to replace the auto feeder valve.
Safe things to check
The pressure gauge is the homeowner's tool here. Note the reading when the system is cold and again when it is hot; a healthy system moves only a little. A gauge that climbs every heating cycle, or one that keeps dropping week after week, points at the feeder, the expansion tank, or a leak.
Look for drips around the feeder and its fittings, and for water at the relief valve discharge. Do not crank the feeder open to raise pressure, and do not leave a manual bypass open after topping up. If pressure keeps moving on its own, the system needs diagnosis.
What a licensed technician will check
A technician tests the feeder as a system, not a part. They measure static fill pressure, confirm the feeder holds it, verify the backflow preventer is present and working, and check the feeder filter or strainer for debris. If the boiler has an automatic fill function, they confirm it operates and resets correctly. They also look for the reason the system needed water — a hidden leak, a failed expansion tank, air being drawn in — because replacing a feeder on a system that is losing water just starts the cycle again.
Where the valve seat is damaged or the reducer will not hold its setting, the feeder is repaired or replaced and the system is refilled, purged and leak-checked. If your boiler's pressure keeps climbing or falling, call ROMA Heating & Cooling; feeder service is straightforward work once the cause is known.
Frequently asked questions
Why does my boiler pressure climb every time it heats up?
Rising pressure usually means the feeder is passing water it should not, or the expansion tank has lost its air cushion and cannot absorb the water's growth. The two work together, so a technician checks both before replacing anything.
Should the automatic fill valve be left open?
No. NTI's manual warns that a feeder left open will keep adding fresh, oxygenated water if the system has a leak, which promotes corrosion and scaling. Feeders are meant to top the system up, not to run continuously.
My system needs water every month. Is that normal?
A sealed system should hold its pressure for a long time. Regular top-ups point to a leak somewhere in the system or boiler, and finding it is better than letting the feeder mask it.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- NTI Trinity Tft 60-399 Installation and Operation Instructions · 99984535 (2024-04-08) · accessed September 9, 2026
- IBC SL 10-85 G3 / SL 14-115 G3 / SL 20-160 G3 / SL 30-199 G3 Installation & Operating Manual · 120-276E13 · accessed September 9, 2026
- Navien NCB-H Service Manual · Version 1.00 (Feb 2021) · accessed September 9, 2026
- Laars Mini-Therm II Residential Gas-Fired Hydronic Boilers (JVS, JVT) Installation & Operating Manual · 1025Y · accessed September 9, 2026
Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.