Skip to content
Boilers.caby ROMA Heating & Cooling

Component

Thermopile

A thermopile, sometimes called a pilot generator or powerpile, is a stack of thermocouples that makes enough voltage to run a millivolt gas valve with no external power. This page explains where thermopiles are used, how they fail, and what a licensed technician checks.

Safety first

If you smell gas, leave the building and call FortisBC at 1-800-663-9911 or 911 from outside. A thermopile holds a gas valve open on its own, so a failed one is a gas-safety part: never jumper around it, never hold the pilot button down to keep gas flowing, and never open the gas valve to test it.

Thermopile and millivolt gas valve work is licensed gas work in British Columbia under Technical Safety BC. Homeowners should treat the pilot assembly, thermopile and valve as one sealed safety circuit that belongs to a qualified technician.

Millivolt systems are often older and may be found on steam or hot-water boilers and some specialty equipment. Age makes professional inspection more important, not less.

What it does in a gas boiler

A thermopile is several thermocouples connected in series inside one probe. Because each junction adds its small voltage to the next, the stack produces enough millivolts to operate a millivolt gas valve directly, with no 24-volt transformer and no household power needed for the safety circuit. In the trade it is also called a pilot generator or, by Honeywell's historic name, a powerpile.

Slant/Fin's Galaxy steam boiler manual shows the arrangement: the pilot flame must engulf the thermocouple, powerpile generator or flame sensor, and the technician adjusts the pilot until a steady flame envelopes 3/8 to 1/2 inch of the probe tip. When the pilot is lit, the generator holds the valve open; if the flame goes out, the valve closes.

Thermopiles appear on older millivolt boilers and in conversion parts. Weil-McLain's Canadian service parts catalogue lists thermopile replacements and a conversion kit that changes a thermocouple system to a thermopile, along with 20-millivolt conversion kits for its CGa boilers. Viessmann's historic manual index likewise includes millivolt installation and operating manuals for its Vitogas 050 ECD line, showing how common the technology once was.

How it fails

Like any thermocouple, a thermopile loses output as it ages: oxidation, soot and heat cycles reduce the millivolts it produces until the gas valve no longer stays open reliably. The symptom is a pilot that holds only while the button is pressed, or a boiler that lights when the room is warm and fails when it is cold, because the valve needs more voltage than the generator can supply.

Pilot condition is the other half of the circuit. A weak, yellow or misaligned pilot flame heats the thermopile tip poorly, and a dirty pilot orifice or blocked ports produce exactly that. Slant/Fin's manual treats the pilot flame envelope as a service specification for this reason.

Connections and wiring are the third failure point. Millivolt circuits run at very low voltage, so a corroded terminal or a loose fitting adds enough resistance to stop the valve working even when the thermopile itself is healthy. That is why technicians measure the circuit under load rather than just looking at the pilot.

Safe things to check

Homeowners can report whether the pilot stays lit on its own, whether the main burner ever fires, and whether the problem is worse in cold weather. Those details point a technician toward a weak generator or a connection issue before the visit begins.

Do not press and hold the pilot button to run the boiler, and do not remove or bend the thermopile. If the pilot will not hold, turn the boiler off and call for service. If you smell gas, leave and call FortisBC at 1-800-663-9911 or 911 from outside.

Keep the boiler and its controls accessible, and mention any recent conversion or parts replacement, because millivolt systems are often modified over the years and the parts fitted may not match the original design.

What a licensed technician will check

A technician verifies the pilot flame first, cleaning the pilot and setting the flame envelope to the manual's specification. Then the thermopile is tested with a millivolt meter, both open-circuit and under load, and the readings are compared with the manufacturer's data for the valve it serves. A generator that reads low is replaced, and the new part is re-tested through several cycles.

The technician also checks the millivolt wiring and terminals for corrosion, verifies that the gas valve responds correctly, and confirms that the safety circuit closes when the pilot is lost. Where a boiler has been converted between thermocouple and thermopile systems, the correct kit and valve matching are part of the repair.

Because millivolt boilers are older, the visit is also a chance to look at the pilot assembly, heat exchanger and venting as a system. If your millivolt boiler will not hold its pilot or fire reliably, call ROMA Heating & Cooling for a diagnosis.

Frequently asked questions

What is the difference between a thermocouple and a thermopile?

A thermocouple is one junction producing a small millivolt signal, used to hold a pilot safety valve open. A thermopile is several thermocouples in series, producing enough voltage to operate a millivolt gas valve and even simple controls without external power.

Why does my millivolt boiler work better in warm weather?

A weakening thermopile produces less voltage as it ages, and a millivolt valve needs a minimum to stay open. Cold can push a marginal circuit below that threshold, which is why the failure often shows up first on cold mornings.

Can I replace a thermopile myself?

No. It is part of the gas valve safety circuit and sits in the pilot assembly on the gas side of the appliance. In BC the work is licensed, and the replacement must match the valve's millivolt requirements.

Book a consultation

A technician reviews your building and options. Requests are confirmed by ROMA.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate