Component
Transformer
The transformer is the small component inside the boiler that steps household 120-volt power down to the low voltage the controls use — typically 24 volts AC. It powers the control board, the thermostat terminals, zone valves and the safety circuits, and when it fails, the boiler can go completely dead. This page explains the transformer's job, how it fails, and what a licensed technician checks.
What it does in a hydronic system
A boiler's control system does not run on household voltage. The transformer converts 120-volt AC from the wall into the low voltage the electronics and control circuits need. Navien's NCB-H installation manual describes the internal 24-volt transformer as rated for 75 VA and notes that it provides power to the zone valve, low-water cut-off and thermostat terminals — a single transformer feeding all the low-voltage loads on the boiler.
The manuals also give the transformer's limit. Navien warns that if the total power consumption of all three zone valves exceeds 72 VA, an external zone valve controller must be used, because the boiler's own transformer cannot carry more. That single sentence explains a whole class of failures: an installer adds a zone without checking the load, the transformer runs at its ceiling, and years later the boiler develops intermittent low-voltage problems that are hard to trace.
It helps to know there are two transformers on many boilers doing very different jobs. The control transformer steps voltage down for the electronics, while the ignition transformer steps voltage up — Navien's service manual lists an ignition transformer with a 120-volt, 60-hertz input and an output around 20 kilovolts to fire the spark. The two are separate parts, and a technician tests them separately.
How it fails
Transformers fail from overload, heat and age. A shorted thermostat wire, a failing zone valve or a load beyond the rated capacity makes the transformer run hot until its windings fail or its internal thermal protection opens. The result can be complete: no display, no fan, no pump, and a boiler that will not even attempt to ignite. IBC's SL G3 troubleshooting guide lists exactly that pattern — boiler will not attempt to ignite, fan and pump off, display not illuminated — and names a defective transformer as the diagnosis, with a check, reconnect or replace instruction.
A failing transformer can also produce partial symptoms. IBC documents an Error - Module High Current for a condition where the 24-volt supply to the ignition module and gas valve is exceeded, with a check of the transformer output as the first fix. A transformer that sags under load may run the display but drop out when the gas valve or a zone valve energizes, producing intermittent lockouts that seem to come and go.
Because the transformer feeds the safety circuits as well as the comfort circuits, its failure is treated as a no-heat emergency rather than an inconvenience — the boiler cannot prove flame or monitor its limits without it.
Safe things to check
The safe checks are at the panel and the phone. Note whether the display is lit, whether the boiler responds at all, and whether the breaker has tripped. If the display is dark, IBC's own sequence starts with the transformer, so tell the technician the display is out — that one detail points them straight at the low-voltage supply.
Do not open the boiler cabinet to look at the transformer, and do not replace a fuse with a larger one. The transformer's low-voltage side connects to the gas valve and safety circuits, and the high-voltage side is line power. Both belong to the licensed technician.
What a licensed technician will check
A technician verifies the transformer rather than guessing. On IBC's platform, the service path for a blank screen or a no-ignition, no-display condition is to check the transformer output and replace it if damaged, then inspect the circuit board. On Navien's NCB-H, the wiring diagram shows the transformer's connections to the main board, so the technician can confirm input voltage, output voltage and the loads it feeds.
The load side matters as much as the transformer. The technician checks the thermostat wiring and zone valves for shorts or excessive draw — the reason Navien sets the 72 VA ceiling — because a new transformer installed on a shorted circuit will fail the same way. Where the transformer has failed, it is replaced with the correct part and the boiler is cycled through a full heating sequence to confirm the low-voltage circuits hold up under load.
If your boiler is dead or the display will not light, call ROMA Heating & Cooling. Transformer faults are among the more straightforward repairs on a modern boiler once the circuit is tested properly.
Frequently asked questions
Why does my boiler have two transformers?
They do opposite jobs. The control transformer steps 120-volt power down to 24 volts for the board, thermostats and zone valves; the ignition transformer steps voltage up — Navien's service manual lists an output around 20 kilovolts — to fire the spark. A technician tests each one separately.
Can I add another zone valve to my boiler?
Only if the boiler's transformer can carry it. Navien's manual rates the internal transformer at 75 VA and requires an external zone valve controller when three zone valves would draw more than 72 VA. Your heating contractor can check the load before adding a zone.
My display is dark and the boiler is silent. Is it the transformer?
It is one of the first things a technician checks. IBC's guide pairs a defective transformer with the exact symptom of a boiler that will not ignite while the fan, pump and display are off. The transformer and its circuit are tested before any part is replaced.
Book a consultation
A technician reviews your building and options. Requests are confirmed by ROMA.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- Navien NCB-H Installation and Operation Manual · accessed September 9, 2026
- Navien NCB-H Service Manual · 1.00 (Feb 2021) · accessed September 9, 2026
- IBC SL 26-260 G3 / SL 40-399 G3 Commercial Installation & Operating Manual (V-10 controller) · 120-270E12 · accessed September 9, 2026
- FortisBC — Appliance maintenance and safety · accessed September 9, 2026
Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.