Skip to content
Boilers.caby ROMA Heating & Cooling

Problem

Boiler leaking water

Water appearing on or under a gas boiler: how to tell a real leak from normal condensate, what usually causes boiler leaks, and why ROMA recommends professional isolation of a wet gas appliance.

Safety first

If you smell gas, leave the building and call FortisBC at 1-800-663-9911 or 911 from outside before anything else. A water leak with no gas smell is handled differently: keep water away from electrical outlets and appliances, contain drips in a bucket, and do not touch pooled water near the boiler's wiring.

A wet gas appliance should be isolated by someone who can do it safely, because water and the boiler's electrical and gas components do not mix. If water is running over the casing or pooling underneath, the conservative move is to shut the boiler off at its service switch if you can reach it from dry ground, and call for an assessment before using the system again.

What is happening

Not every wet spot under a condensing boiler is a leak. Condensing boilers, the common type in modern BC homes, produce acidic water vapour that drains away as condensate, and a dripping condensate line or a poorly seated trap can look exactly like a boiler leak. The question is whether the water is supposed to be there, and where it is coming from.

A genuine pressure leak usually appears while the system is running or pressurised: drips from the boiler body, from pump and valve connections, or along the discharge path of the pressure-relief valve. Water that appears only when the boiler fires, or that smells or stains differently from the condensate drip, points to the heating loop rather than the drain.

Safe things to check at home

Note where the water is: under the boiler, at a fitting, at the condensate line, or along the small discharge tube of the pressure-relief valve. Check whether the drip is continuous or only while the boiler runs, and whether the water is clear like condensate or discoloured like system water. A bucket under a steady drip protects the floor while you decide what to do.

Read the pressure gauge cold to see whether the system is losing pressure, and write down any alert on the display before you shut anything off. Do not open the boiler casing, tighten fittings under pressure, or attempt to stop a leak by force. If the drip is at the relief valve's discharge tube while the boiler is hot, that is a pressure problem worth reporting rather than a valve to be wedged.

Common causes

Leaks around the outside of the boiler usually come from fittings, valves and components: a weeping pump seal, a dripping fill valve, a leaking connection at the expansion tank or air separator, or a pressure-relief valve that is passing. Inside the casing, the serious possibility is the heat exchanger itself, where corrosion or age can open pinholes that leak system water.

Condensate-side wetness is common on condensing boilers: a trap that has come loose, a neutralizer that overflows, or a drain line that has sagged and filled with water. On combination boilers an internal leak in the domestic heat exchanger can let system water mix with tap water in ways that show up as pressure loss or odd water behaviour rather than a visible drip. Distinguishing these requires opening the casing and watching the boiler run, which is technician work.

Where boilers leak, and what each spot usually means

Leaks leave a trail, and where the water appears narrows the search before anything is taken apart. A drip from the small discharge tube that runs from the pressure-relief valve is the system telling you it reached the relief setting, which points at overpressure rather than at the valve itself: an expansion tank that has lost its air charge, a system that is overfilled, or a fill valve that will not stop feeding are the usual reasons. The discharge tube should be dry when the system is behaving.

Water at the boiler body, around a pump flange, at an air separator or where the expansion tank connects is more often a seal or gasket that has hardened with age and heat. Joints that weep only when the system is hot are the classic version, because the metal has expanded; they can stay dry all summer and show up in the first cold snap. A weeping auto-fill or pressure-reducing valve is another possibility, and it can quietly hide a pressure loss by topping the loop up on its own.

Some leaks do not leave a puddle. A hidden run of in-floor tubing, or piping buried in a wall or ceiling chase, can lose water for months and show up only as a falling cold pressure reading or a warm, damp patch on a floor or ceiling. On a combination boiler, a leak inside the domestic hot-water plate heat exchanger or an internal connection can send system water down the condensate path, which looks like a normal condense drain rather than a leak.

Finally, remember that condensing boilers make water by design. A loose or unseated condensate trap, an overflowing neutralizer, or a sagged drain line that holds water can look exactly like a boiler leak while being a simple drain repair. The point of finding the spot is that these very different causes carry very different repairs, and none of them should be diagnosed from the puddle alone.

A leak that only appears when the heating is on

When a drip starts only once the boiler fires and stops again when it cools, the pattern itself is evidence. Metal expands as it warms, so a joint or gasket that is marginal can stay sealed when cold and weep once it reaches temperature, then seal again as it cools. The same firing cycle makes condensate: a condensing boiler produces water only while it burns, so a trap or drain that looks dry in summer can overflow every time the boiler runs.

Temperature also decides when a pressure-relief valve passes. A system that is overfilled, or whose expansion tank has lost its air charge, reaches its highest pressure at the end of a burn, when the water has expanded the most, which is when the relief valve discharges. A drip that appears only while the boiler is hot therefore points at pressure and thermal movement rather than at a hole that is always open, and it is a reason to read the gauge cold and again when hot rather than to reach for a wrench.

Telling a boiler leak from a plumbing leak

Water near a boiler can come from three different places, and they are fixed by different work: the boiler's sealed heating loop, the home's mains-pressure plumbing, and the domestic hot-water path inside a combination boiler. The pressure gauge is the simplest divider. If the system's cold gauge reading is falling along with the drip, water is leaving the sealed heating loop, which is the boiler's own circuit. If the gauge holds steady while water still appears, the source is more likely the mains-pressure side: a household supply pipe, a fixture, or the cold feed to the boiler.

Timing adds a second divider. Water that appears only while the boiler fires and the loop is pressurised, or that tracks the heating cycle, points at the loop. Water that appears whenever a hot tap runs, or that shows up at a fixture or a branch of pipe away from the boiler, points at the domestic side or at household plumbing. Water that appears continuously whether the boiler runs or not, and leaves the gauge unchanged, is usually a mains-pressure leak that happens to be near the appliance rather than a boiler fault.

A combination boiler straddles both worlds, which is why its leaks can be confusing. It holds a sealed heating loop and a mains-pressure domestic water path inside one casing, so a drip can come from either. Water that appears only when a tap is open, that changes with the tap, or that shows at the boiler's cold inlet is on the domestic side; water that appears with the heating cycle and takes the pressure gauge down with it is on the loop side. Only a technician can confirm which by isolating and testing, but notes about timing and the gauge point the visit in the right direction.

One practical test is available where the boiler has a clearly labelled isolation valve on its cold-water feed and it can be reached from dry ground. Closing that valve stops new mains water entering the appliance, so a drip that continues points at the loop or the drain path, while a drip that stops points at the domestic side or the feed. If anything about the valve is unclear, or reaching it means crossing water near wiring, leave it alone and let the technician isolate the system. Nothing about a leak is a reason to touch the gas side, and a gas smell changes the priority entirely: leave the building and call FortisBC's emergency line at 1-800-663-9911 or 911 from outside.

Knowing which circuit is leaking matters because the consequences differ. A heating-loop leak drops system pressure, which can shut the boiler down on low-water protection, and a leak inside the heat exchanger can mean the appliance is near the end of its life. A domestic-side or mains leak is a water-damage and plumbing problem first. Both belong to a licensed technician, and both are easier to fix when the first person on the scene has written down whether the gauge moved, when the water appears, and what the boiler was doing at the time.

Why a drip is more than a nuisance

Water in the wrong place is a building problem before it is a boiler problem. A slow leak under a boiler can soak flooring, subfloor, drywall and framing, feed mould in a crawl space or a wall cavity, and damage anything stored nearby. In a Greater Vancouver home, where much of the year is damp anyway, a hidden leak that keeps the surrounding structure wet is the kind that turns a small repair into a larger one, and the sooner it is stopped the less material has to be dried or replaced.

There is a mechanical cost as well. Every time the fill valve tops the loop up to replace lost water, fresh water carrying dissolved air and minerals enters a system that was designed to hold the same water for years. Manufacturer guidance warns that continual makeup water shortens boiler life because minerals build up in the heat exchanger and reduce heat transfer. So a boiler that keeps needing a top-up, and keeps weeping it away again, is being slowly harmed by the very water that is supposed to keep it working.

That is why a steady drip should not be filed under 'next service'. Water near the boiler's electrical and gas components is a safety matter as well as a maintenance one, and a leak that tracks onto a burner, a control board or a wiring harness can do damage that is far more expensive than the original fitting.

What to do while you wait for a technician

The first job with a leak is to keep water away from things water damages and away from anything electrical. If the boiler's service switch can be reached from dry ground, turning it off stops the appliance from firing while the leak is assessed; if water is pooling near wiring, controls or the gas connection, do not reach through it. Put a bucket or shallow container under a steady drip and clear anything stored nearby, and if you can see and safely reach a clearly labelled isolation valve on the boiler's cold-water feed, closing it limits how much more water can enter the loop. If anything is unclear, leave it untouched and wait for the technician.

Do not open the casing or tighten fittings under pressure, and do not try to stop a drip at the pressure-relief valve by wedging or plugging its discharge tube. That tube is a safety path: if it is passing, the system is over pressure, and blocking it removes the protection rather than the leak. Leave the boiler off if you are not sure it is safe to run, and if you smell gas at any point the leak stops mattering, so leave the building and call FortisBC's emergency line at 1-800-663-9911 or 911 from outside.

Write down what you saw before you shut anything off: where the water appears, whether it is clear or discoloured, whether it drips only while the boiler fires, and the cold pressure-gauge reading. Those four observations let a technician bring the right tools and tell a condensate fix from a loop repair before arriving, and they are the details to give when you call ROMA Heating & Cooling at 778-909-5731.

A leak that starts after a service, repair or drain-down

A leak that appears in the days after a service, a repair or a drain-down is a common and understandable event, and its timing is useful rather than alarming. Opening a sealed loop lets water out and lets air in, and refilling it re-pressurises joints, seals and valves that may have sat undisturbed for years. A fitting that was loosened and re-tightened can weep, a seal that dried while the system was drained can pass once it is wetted again, and a drain or purge valve that was used and not fully closed is a straightforward cause.

The condensate side is worth checking first on a condensing boiler, because it is the part most often disturbed during a service and the part most likely to look like a leak. A trap that was cleaned and not fully reseated, a drain line that was pushed back on only part way, or a neutralizer that was opened and not sealed again will drip clear water exactly where the boiler sits. Clear water from the drain path and discoloured system water from a joint tell different stories, and the condensate route can be looked at from outside the casing without opening the appliance.

Pressure is the other thing a recent visit can change. A system refilled after a drain-down can sit slightly above its cold set point, and an overfilled loop reaches the relief valve's setting sooner when it heats, so the discharge tube weeps once the boiler runs. That is a pressure condition rather than a failed valve, and it is corrected by setting the cold fill to the figure the boiler's own manual specifies, which is part of the commissioning a technician performs rather than a homeowner adjustment. A drip at the relief-valve discharge tube is never something to plug or wedge, because that tube is the system's safety outlet.

When a leak follows work, the first call belongs to whoever did the work, and the notes to give are simple: what was done, when, where the water now appears, and whether the cold gauge has moved. A return visit under the same job is normal practice and far cheaper than a fresh diagnosis. Keep the service record and the completed checklist with the appliance documents, because they establish what was touched and when, and Technical Safety BC's annual servicing bulletin expects that checklist to carry the contractor's and the gas fitter's names. If the work involved gas, the gas side is not a homeowner repair: a licensed gas fitter verifies the supply and the connections, and any gas work in British Columbia is carried out under Technical Safety BC's permit system.

Repair or replace: what the leak's location tells you

Most boiler leaks are repairable, and where the water starts is the best guide to which kind you have. Water at a pump flange, an air separator, the expansion tank connection or a valve is usually a seal, gasket or component that has aged, and those repairs are ordinary service work. A drip from the pressure-relief valve's discharge tube is an overpressure symptom, such as a waterlogged expansion tank, an overfilled system or a fill valve that will not shut off, and the fix is the cause rather than the valve. Condensate-side wetness on a condensing boiler is often a trap, neutralizer or drain-line issue that is simpler still.

The leak that changes the conversation is the one from inside the heat exchanger. Corrosion or age can open pinholes in the exchanger, and a leak there usually means the boiler has reached the end of its service life; a technician will say so with the reasoning and discuss replacement rather than a repair that cannot be made reliable. An internal leak on a combination boiler's domestic side is a related but different fault, and it can send system water down the condensate path in a way that shows up as pressure loss rather than a puddle.

That is why a leak should be isolated and traced rather than just mopped up. The same puddle can mean a short seal repair or a replacement decision, and only opening the appliance and watching it run through a firing cycle settles which it is. Any gas-side work that follows is done by a licensed contractor under Technical Safety BC's permit system, with combustion verified before the boiler returns to service.

What to record before you call

A leak is easiest to fix when the person who saw it first writes down what they saw. Note exactly where the water appears, whether it is clear like condensate or discoloured like system water, and whether it drips continuously or only while the boiler fires. Read the pressure gauge with the system cold and write the number down, and if the boiler has a display, record any code before switching anything off. A photograph of the wet area, taken from a safe distance, is worth more than a description when the technician is deciding what to bring.

Those details decide whether the visit is a condensate repair, a seal replacement or a heat-exchanger assessment, and they also decide how urgent it is. Water near wiring, controls or the gas connection is a safety matter, and the boiler should be left off until it has been assessed. If a gas smell is present at any point, the leak stops being the priority: leave the building and call FortisBC's emergency line at 1-800-663-9911 or 911 from outside before anything else.

When to call

Call when water is actively leaking from the boiler or its connections, when the drip is steady enough to need a bucket, or when the system is losing pressure along with the leak. A heat-exchanger leak can worsen quickly, and water near electrical and gas components is never a wait-and-see situation.

If the boiler is safe to leave off, switch it off and call. If you are not sure the boiler is safe to run, do not run it. Call ROMA Heating & Cooling at 778-909-5731 during business hours and describe where the water is, what it looks like, and whether the drip changes when the boiler fires.

What a licensed technician will do

A technician isolates the boiler, dries the surfaces, and watches it through a firing cycle to find where the water starts rather than where it lands. Pressure tests separate a loop leak from a component leak, and the relief valve, expansion tank and condensate path are each checked against the manual's procedures.

External leaks are often fixed by replacing a seal, valve or fitting. A leaking heat exchanger usually means the boiler needs replacement, and the technician will say so plainly with the reasoning. Any repair that touches the gas side is performed by a licensed contractor under Technical Safety BC's permit system, and combustion is verified before the boiler returns to service.

Frequently asked questions

Is water under a condensing boiler always a leak?

No. Condensing boilers produce water by design, and a dripping condensate connection can look alarming while being a simple fix. The source has to be identified before the severity is known.

Can I tighten a leaking fitting myself?

Fittings under system pressure and anything inside the boiler casing should be left to a technician. Turning the wrong connection can turn a drip into a spray or disturb gas components nearby.

Does a leaking boiler always need replacement?

No. Many leaks come from external valves, seals and fittings that are repaired on their own. Only a leak inside the heat exchanger or a badly corroded boiler body typically ends in replacement.

The pressure-relief valve tube keeps dripping. Is that a leak?

That tube should be dry when the system behaves. A drip there means the relief valve reached its setting, so the cause is usually overpressure from an expansion tank that has lost its charge, an overfilled system, or a fill valve that will not shut off.

Why does the leak only appear when the heating is running?

Heat makes metal expand, so a joint that is marginal can stay sealed when cold and weep once it warms up. A leak that follows the firing cycle points at a connection or seal rather than a hidden hole in the piping.

Can a small hidden leak wait until my next service?

It is better not to wait. A hidden drip can wet flooring, framing and insulation for months, grow mould, and keep the fill valve adding fresh water that shortens boiler life. Hidden loss is worth tracing as soon as it is noticed.

What should I do first if the boiler is leaking?

Keep water away from electrical components, turn the boiler off at its service switch if you can reach it from dry ground, contain the drip in a bucket, and call for an assessment. Do not open the casing or tighten fittings under pressure, and if you smell gas, leave the building and call FortisBC from outside first.

Is a leaking boiler an emergency?

Treat it as urgent. Water near the boiler's electrical and gas components is a safety matter, pressure loss can worsen the fault, and a heat-exchanger leak can grow quickly. It is not a wait-for-next-service item.

How do I tell whether it is condensate or a real leak?

Condensing boilers make water by design, so a wet condensate trap or drain is not a pressure leak. Look at the route the water takes and whether the drip changes when the boiler fires; clear water from the drain path and discoloured water under the casing tell different stories. The source is confirmed by watching the boiler run.

Can a leak cause the boiler to lock out?

Yes. Water in the wrong place can trip an electrical or safety component, and a leak that drops system pressure can trigger low-water protection on some controls. A lockout alongside a leak is a reason to have the appliance isolated and assessed rather than reset repeatedly.

Why does my boiler only leak when it is running?

Heat expands metal, so a marginal joint can seal when cold and weep once warm, and a condensing boiler only makes condensate while it burns. A relief-valve drip that appears at the end of a burn points at pressure, not at a permanently open hole.

Is water from the condensate pipe normal?

Yes. A condensing boiler produces condensate by design, and clear water leaving through the drain path is expected. The concern is a trap that has come loose, a neutralizer that overflows, or water appearing where the drain does not run, which is confirmed by watching the boiler fire.

Can a leaking boiler fix itself?

No. Scale or debris can briefly block a small opening, but the cause remains and the leak returns, often worse. A leak should be traced and repaired rather than waited out, especially where water can reach electrical or gas components.

How can I tell if water under my boiler is from the boiler or from the plumbing?

Read the boiler's pressure gauge cold. If the reading is falling with the drip, the water is leaving the sealed heating loop. If the gauge holds steady and water still appears, the source is more likely the mains-pressure plumbing or the domestic hot-water side, especially if the water shows up when a tap runs.

My boiler started leaking right after it was serviced. What should I do?

Note when the work was done and where the water appears, then call the contractor who did it. A fitting disturbed during the visit, a condensate trap that was not reseated, or a system left slightly overfilled are the usual causes, and a return visit under the same job is the normal and cheapest route.

Can I keep using my boiler while it is leaking?

Only if it is clearly safe. Water near the boiler's electrical or gas components is a reason to leave it off until it has been assessed, and a leak that is dropping the system pressure can lead to a low-water shutdown. If you are unsure, leave the boiler off and call.

Talk to a boiler technician

Describe what the boiler is doing and get a straight answer about the next step.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 15, 2026. Last updated September 15, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate