Problem
Cold heating zones
Why some rooms, radiators or in-floor loops stay cold while the rest of the house heats normally, what to check zone by zone, and how a technician finds the failing link.
What is happening
Most BC boiler homes are divided into zones: groups of radiators or in-floor loops that share a thermostat and open or close together through a zone valve or a zone circulator pump. When one zone stays cold while others heat normally, the boiler is usually fine and the fault sits between that zone's thermostat and the water flowing to its emitters.
The symptom can be a single cold radiator in an otherwise warm zone, a whole floor that never warms, or an in-floor area that takes much longer than it used to. Which pattern you see matters, because a whole zone that is dead points to valves, pumps or controls, while one cold radiator points to that radiator's own valve or trapped air.
Safe things to check at home
Start with the zone's own thermostat: is it set above the room temperature and calling for heat, with fresh batteries if it uses them? Check that the thermostat is not in a schedule holding the zone off. For radiators, confirm the valve on each cold unit is open; hand wheels and thermostatic heads can end up turned down without anyone noticing.
Feel the temperature pattern on a cold radiator: warm at the top and cold at the bottom suggests flow through the valve but poor circulation or trapped air, while a radiator that is cold along its whole length suggests no flow at all. Note whether the boiler fires when the cold zone calls, and read the pressure gauge cold. Write down any alert on the boiler display and look it up on the brand's error-code pages; leave bleeding and valve disassembly to a technician.
Common causes
Air is a frequent culprit: a zone that was drained for a repair, a new radiator, or a system that has slowly collected air can leave one loop circulating poorly. Zone hardware fails too: a zone valve whose motor or end switch has failed may never open fully or may never tell the boiler to fire, and a dedicated zone pump can seize after a summer of sitting idle.
Control-side faults are just as common: thermostat wiring, a controller output that has stopped switching, or a schedule or setpoint error. Balance and flow problems appear as symptoms too, such as a balancing valve closed after renovations, sludge narrowing an old radiator's connection, or an in-floor manifold loop with its isolation valve left shut. A zone that calls but never delivers usually has one failing link somewhere in that chain.
When to call
Call when a whole zone has stopped heating, when a cold zone is accompanied by a boiler that will not fire for it, or when one part of the house is cold enough to be uncomfortable while the rest overheats. Cold rooms in a rented or strata building are also a fairness problem for whoever pays the heating bill.
A single cold radiator is worth reporting too if it does not recover on its own, since the cause may be a failing valve or a radiator that needs attention. Call ROMA Heating & Cooling at 778-909-5731 during business hours and describe exactly which rooms are cold and whether the boiler fires when their thermostat calls.
What a licensed technician will do
A technician traces the zone's call from the thermostat through the controller to the valve or pump, confirming with a meter where the signal stops and whether the valve opens and its end switch closes. On pump zones the pump's operation and current draw are tested rather than assumed from its hum.
Trapped air is removed by purging the zone with the boiler's fill pressure, and the system is re-balanced where radiators heat unevenly. Failed actuators, pumps, thermostats or wiring are repaired or replaced, and the technician verifies that the zone now delivers heat while the boiler cycles normally. Where the cause turns out to be a design problem, such as a zone that can never balance, the options are explained before any work begins.
Frequently asked questions
One radiator is cold but the rest of the room is warm. Why?
The fault is usually local: the radiator's own valve may be shut, the radiator may be air-bound, or sludge may be narrowing the connection. A technician vents and checks it in minutes.
Why does my in-floor zone take hours to warm up?
In-floor loops heat the slab, not the air, so slow response is normal. A zone that used to be faster may have air, a partially closed manifold valve or a failing pump.
Can a cold zone make the boiler short cycle?
Yes. A zone valve that opens only partway lets little water flow, so the boiler reaches its temperature quickly and cycles while the room stays cold.
Talk to a boiler technician
Describe what the boiler is doing and get a straight answer about the next step.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Related
Sources and verification
- FortisBC — appliance maintenance and safety · accessed September 7, 2026
- Technical Safety BC — homeowner gas permits · accessed September 7, 2026
Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.