Skip to content
Boilers.caby ROMA Heating & Cooling

Problem

No heat from the boiler

A gas boiler that has stopped heating the home: how to check the thermostat, power and boiler display safely, what usually causes a no-heat condition, and when to call ROMA Heating & Cooling.

What is happening

A no-heat situation means the rooms are not reaching the thermostat setpoint, and the cause can sit anywhere between the thermostat on the wall and the burner inside the boiler. The boiler may be off, locked out with an alert on its display, firing but not circulating heat, or simply never receiving the call for heat from the thermostat and zone controls.

In Greater Vancouver's climate the failure can arrive during a mild spell, when the boiler has sat idle and a fault has gone unnoticed, or in the middle of a cold snap when it matters most. Homes with radiators feel the drop differently from homes with in-floor loops, which respond slowly in any case, so compare the room temperature with the thermostat rather than judging by touch alone.

Safe things to check at home

Start at the thermostat: confirm it is set above the current room temperature, that it is in heating mode rather than off or cooling, and that batteries are fresh where it uses them. Confirm the boiler's service switch is on and that no breaker in the panel has tripped; a tripped breaker or an off switch accounts for a surprising share of no-heat calls.

Read the boiler's display and write down any alert text or code, then look it up on this site's brand error-code pages. If the manufacturer's manual for your boiler describes a user reset, you may reset once and see whether the boiler resumes; repeated resetting is not a fix and some controls lengthen their lockout with every attempt. Check whether other gas appliances in the home work, glance at the outdoor vent terminal from a safe distance, and note the pressure gauge reading. If you smell gas at any point, leave the building and call FortisBC or 911 from outside first.

Common causes

No-heat faults group into a few families. The boiler may be locked out by an ignition, sensor or safety condition that the display records. The call for heat may not be reaching the boiler because of thermostat wiring, a failed zone valve or circulator, or a controller that is not switching. The gas supply can be interrupted at the meter, a shut-off valve, or by an unrelated event such as a utility interruption.

Low system pressure can stop some boilers with their own low-water protection, and trapped air can leave a system warm at the boiler but cold in the rooms. On combination boilers a fault in the domestic-hot-water circuit can also stop the appliance entirely depending on the design. An alert on the display narrows the search, but a code is not a diagnosis; several different faults can end in the same lockout.

When to call

Call when the boiler is locked out and will not stay running, when a zone is cold and the checks above did not help, or when heat is needed for young children, older adults or anyone whose health depends on a warm home. For a strata building or a home with tenants, an unheated building can also put pipes at risk.

There is no reason to wait through repeated resets. Call ROMA Heating & Cooling at 778-909-5731 during business hours, and be ready to say what the display shows, whether any zone is still warm, and whether other gas appliances are working; that conversation often shortens the diagnosis.

What a licensed technician will do

A technician starts with the boiler's fault history and the alert on the display, then works outward: confirming the thermostat call reaches the boiler, testing zone valves and circulators, checking gas pressures and ignition components, and verifying sensors against the values in the manufacturer's manual. Only after the fault is confirmed by testing is a repair proposed.

If air is the problem the system is purged zone by zone. If a component is at fault it is repaired or replaced with the boiler returned to service and combustion verified. Gas-side repairs are performed under Technical Safety BC's permit system by licensed contractors, which is standard practice in British Columbia.

Frequently asked questions

My boiler shows an error code but is not heating. What should I do?

Write down the exact code and look it up on the brand's error-code pages on this site for its documented meaning. Then call for a diagnosis; the code describes a condition, not the full story.

Is it safe to keep resetting the boiler until it stays on?

No. Reset once if your manual allows a user reset, and call if the fault returns. Repeated resets can hide the underlying problem and extend lockouts on some controls.

The thermostat says it is calling but nothing happens. What is wrong?

The call can be lost in wiring, a zone valve that never opens, a dead circulator or a boiler that is locked out. A technician tests each link in the chain to find where the signal stops.

Talk to a boiler technician

Describe what the boiler is doing and get a straight answer about the next step.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate