Skip to content
Boilers.caby ROMA Heating & Cooling

Problem

Pressure relief valve discharging water

A pressure-relief valve that drips or blows water is the system telling you something: what the valve protects, why it discharges, and why the cause is treated rather than the symptom.

What is happening

The pressure-relief valve is the heating system's pressure safety: it is set to open at a rating the loop should never reach, and when pressure passes that point it discharges water through a small drain tube to keep the system from overpressurising. A valve that drips or blows has done its job; the question is why the system pushed it to its limit.

Discharge patterns are information. A drip only while the boiler runs hot points at expansion, a drip that never stops can point at overfilling or a valve that will not reseat, and a full discharge usually marks a genuine overpressure event. Water on the floor near the discharge tube, or a tube that has clearly run recently, is the visible record of all three.

Safe things to check at home

Place a container under the discharge tube if it is dripping, keep the area clear and dry, and note when the discharge happens: only while the boiler fires, only when cold, or constantly. Read the boiler's pressure gauge cold and again after running, write both numbers down, and note any alert on the display to look up on this site's brand error-code pages.

Never wedge, tape or hold the relief valve shut, never open it manually to test it, and never cap its discharge tube; the valve is a safety device and its drain path must stay open. If water is discharging steadily, leave the boiler's operation to a technician's judgement rather than to improvised fixes.

Common causes

The valve discharges for one of three reasons: the system genuinely overpressurised, the valve has failed and passes at normal pressure, or the discharge is a leftover from an earlier event that the valve never sealed again. Overpressure usually traces to a failed expansion tank, an overfilled system fed by a stuck fill valve, or a boiler that ran away on temperature.

A valve that discharges only in a specific pattern, such as while the boiler is hot, tells the same story as the pressure gauge: the system is expanding past what its tank can absorb. Thermal expansion trapped by a check valve or backflow preventer on the cold inlet can also build pressure, and a valve that has discharged once may weep forever afterwards even if the original cause is corrected.

When to call

Call when the valve is dripping or has discharged, especially if the discharge is steady or repeated, and call promptly if the boiler's pressure gauge reads high while it happens. Every discharge is water leaving the loop, which means the system is losing pressure and will soon need the cause found.

Describe the discharge pattern and the gauge numbers when you call. Call ROMA Heating & Cooling at 778-909-5731 during business hours, and the technician will measure the system rather than simply replace the valve.

What a licensed technician will do

A technician confirms what the discharge means: system pressure is measured cold and hot, the expansion tank's air charge is checked, and the fill valve's behaviour is verified before the relief valve itself is judged. The relief valve is then tested against its rating and replaced if it will not reseat.

The underlying cause is corrected as well, whether that means re-charging or replacing the expansion tank, correcting the fill pressure, or replacing a valve that failed on its own, and the system is run through a full cycle to confirm the relief valve stays dry at normal operating pressure. The discharge tube is left clear so the safety device can do its job again.

Frequently asked questions

Is a dripping relief valve an emergency?

A steady discharge is a clear call for service, and one that coincides with high gauge pressure deserves a prompt call. The valve is doing its job, but the system behind it needs measurement.

Why does my relief valve drip only when the boiler is hot?

That pattern usually means expansion is not being absorbed, classically because the expansion tank has lost its charge. The water expands, pressure climbs, and the valve discharges.

Can I cap the relief valve discharge tube?

Never. The discharge tube is the valve's only way to relieve pressure safely, and capping it turns a safety device into a hazard. Leave it open and call a technician.

Talk to a boiler technician

Describe what the boiler is doing and get a straight answer about the next step.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 8, 2026. Last updated September 8, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate