Skip to content
Boilers.caby ROMA Heating & Cooling

Pennco · Error codes

Pennco FSB 2 — Pressure Switch Failed to Open (stuck Closed)

2

Needs attentionPennco FSB cast-iron gas boilers (integrated boiler control error codes, I&O 240013101)

Pressure switch failed to open (stuck closed). The control relies on the pressure switch to verify the inducer motor is running and the vent is clear, but the switch did not open at the end of the heat cycle; check the pressure switch, its tubes and wiring, and replace the control if the code persists. The table classifies it as Error.

Applies to

This venting or air-supply fault code is displayed by the Integrated boiler control (Honeywell 4200 series, numeric error codes) on FSB models (FSB-2 through FSB-6), as documented in Pennco FSB Cast Iron Gas-Fired Boiler Installation, Operation & Maintenance Manual, PN 240013101 Rev. B, Appendix A Table A-2 Operation Error Codes (240013101 Rev. B). Codes can differ between controller generations, so always check the manual that matches your unit.

Controller: Integrated boiler control (Honeywell 4200 series, numeric error codes). Source manual: 240013101 Rev. B.

Why a code is not a diagnosis

A venting or air-supply code points at the combustion-air path: a blocked terminal, a restricted flue, a failed fan, or a condensate restriction. It does not say which, and running an appliance with a blocked flue is unsafe.

Safe things to observe

  • If a carbon-monoxide alarm sounds anywhere in the building, leave immediately and call 911 from outside.
  • From a safe distance, check that the vent terminal and combustion-air inlet are not blocked.
  • Do not run the appliance while a blockage is suspected.

Do not

  • Do not put anything into the vent or air-intake openings.
  • Do not remove or modify vent pipe.

How professional service helps

  1. A technician inspects the full vent and combustion-air path, clears blockages and checks the fan.
  2. Combustion and safety devices are verified with an analyser and the manufacturer's procedure after any repair.

Where ROMA provides on-site service

On-site service is currently offered in Greater Vancouver, BC, including Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Port Coquitlam, Port Moody, Delta, Langley, Maple Ridge, Abbotsford, Chilliwack, White Rock, Pitt Meadows, Tsawwassen, Anmore, Lions Bay, Belcarra, Bowen Island, Mission. Everything else on this site is reference information you can use anywhere in Canada.

See all service areas

Parts and service

Parts commonly involved

These parts appear in the documented text for this alert. A code reports a condition, not a failed part — a technician confirms the cause by testing before anything is replaced.

Service for this alert

  • Gas Boiler Repair

    Licensed gas technicians from ROMA Heating & Cooling diagnose and repair residential and light-commercial gas boilers across…

Every boiler part explained — what it does, how it fails and what a technician checks.

Documented for Pennco FSB Series.

Frequently asked questions

Is this code a carbon-monoxide danger?

The code relates to combustion or venting, so treat any CO alarm as an emergency and call 911 from outside. The appliance itself should be checked by a technician before it runs again.

Can I clear this code myself?

Clearing a code without fixing its cause usually just brings it back. Note the code, check the safe items on this page, then call a licensed technician. If your appliance manual describes a user reset for this exact code and it stays away, no call may be needed.

Boiler locked out? Call with the alert text ready.

The brand, model and this alert are passed along when you request service online, so the technician arrives prepared.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 9, 2026. Last updated September 9, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate