Skip to content
Boilers.caby ROMA Heating & Cooling

Laars Heating Systems · Error codes

Laars FT Series Floor 16 — Operating Temperature Sensor Detects Water Temperature Greater Than 203°f (95°c)

16

Needs attentionLaars FT Series Floor (FTHF heat-only and FTCF combi; numeric fault codes, manuals 1510B / 1505C)

Operating temperature sensor detects water temperature greater than 203°F (95°C). The operating temperature sensor detected a water temperature greater than 203°F, which is likely because the internal boiler pump is not able to move enough water through the heat exchanger, so check the CH inlet pipe for blockage and check the operating temperature sensor resistance. The table classifies it as Hard Lock.

Applies to

This venting or air-supply fault code is displayed by the Laars FT floor control on FT Series Floor models (FTHF199 heat-only and FTCF199 combi), as documented in FT Series Floor Heat-Only Installation and Operation Instructions, Document 1510B (the FTCF combi manual 1505C prints the same code table) (1510B). Codes can differ between controller generations, so always check the manual that matches your unit.

Controller: Laars FT floor control. Source manual: 1510B.

Why a code is not a diagnosis

A venting or air-supply code points at the combustion-air path: a blocked terminal, a restricted flue, a failed fan, or a condensate restriction. It does not say which, and running an appliance with a blocked flue is unsafe.

Safe things to observe

  • If a carbon-monoxide alarm sounds anywhere in the building, leave immediately and call 911 from outside.
  • From a safe distance, check that the vent terminal and combustion-air inlet are not blocked.
  • Do not run the appliance while a blockage is suspected.

Do not

  • Do not put anything into the vent or air-intake openings.
  • Do not remove or modify vent pipe.

How professional service helps

  1. A technician inspects the full vent and combustion-air path, clears blockages and checks the fan.
  2. Combustion and safety devices are verified with an analyser and the manufacturer's procedure after any repair.

Where ROMA provides on-site service

On-site service is currently offered in Greater Vancouver, BC, including Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Port Coquitlam, Port Moody, Delta, Langley, Maple Ridge, Abbotsford, Chilliwack, White Rock, Pitt Meadows, Tsawwassen, Anmore, Lions Bay, Belcarra, Bowen Island, Mission. Everything else on this site is reference information you can use anywhere in Canada.

See all service areas

Parts and service

Parts commonly involved

These parts appear in the documented text for this alert. A code reports a condition, not a failed part — a technician confirms the cause by testing before anything is replaced.

Service for this alert

  • Gas Boiler Repair

    Licensed gas technicians from ROMA Heating & Cooling diagnose and repair residential and light-commercial gas boilers across…

  • Gas Boiler Replacement

    ROMA replaces old, failed or inefficient gas boilers in Greater Vancouver, handling removal, venting and gas-supply changes,…

Every boiler part explained — what it does, how it fails and what a technician checks.

Documented for Laars Heating Systems FT Series Floor.

Frequently asked questions

Can I clear this code myself?

Clearing a code without fixing its cause usually just brings it back. Note the code, check the safe items on this page, then call a licensed technician. If your appliance manual describes a user reset for this exact code and it stays away, no call may be needed.

Boiler locked out? Call with the alert text ready.

The brand, model and this alert are passed along when you request service online, so the technician arrives prepared.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Sources and verification

Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate