Skip to content
Boilers.caby ROMA Heating & Cooling

Guide

Combi boiler vs heating-only boiler with a tank

Published September 7, 2026 · Updated September 15, 2026 · Boilers.ca editorial

Short answer

Choose a combi boiler when the home is compact, tank space is scarce and hot-water draws are modest and sequential; choose a heating-only boiler with an indirect tank when several bathrooms, large tubs or simultaneous draws need a stored reserve of hot water. Sizing the hot-water side separately from the space-heating side matters in both cases.

Two different ideas about hot water

A combi boiler and a heating-only boiler with an indirect tank both warm a home with hydronic heat, and both are sealed condensing gas appliances that vent in certified plastic pipe. The difference is entirely in how they make domestic hot water. The combi heats water as it is used: cold supply runs through a plate heat exchanger while the burner fires, so hot water is produced continuously but only at the rate the appliance can deliver. The system arrangement stores hot water instead: the boiler heats the closed heating loop, and a coil inside an insulated tank transfers that heat to the potable water held in storage, so a volume of hot water sits ready at all times.

That single design choice explains almost every practical difference between the two. Storage gives the household a reserve that can serve several fixtures at once; on-demand production gives the household a smaller mechanical footprint and no stored water to keep warm between uses. Neither is inherently better. The right choice tracks the household's draw pattern, its space, and how much interruption the owners will tolerate when a hot-water event and the heating call for the same burner.

What 'system boiler' means in a Canadian home

The phrase 'system boiler' comes from the United Kingdom, where it describes a boiler that heats the home and a separate stored-hot-water cylinder, with the circulating pump and expansion vessel built into the appliance instead of mounted remotely. In British Columbia the same arrangement is normally called a heating-only boiler paired with an indirect storage tank: the boiler warms the hydronic loop and reheats the tank, and domestic hot water is drawn from storage rather than made on demand.

That is why 'combi versus system boiler' needs a translation before it can be answered here. The meaningful question in Greater Vancouver is not which label applies but whether the home stores its hot water in a tank or makes it on demand through a combi. The other terms a homeowner will meet — 'regular boiler', 'heat-only boiler', 'conventional boiler' — are used inconsistently from one manufacturer's literature to another, so the reliable way to classify an appliance is to ask three questions: is there a hot-water storage tank, does the appliance contain its own pump and expansion vessel, and is the system sealed or open to atmosphere. In this region nearly every new residential installation is a sealed system, which leaves the tank-or-no-tank choice as the one that actually decides the design.

What the combi does well, and where its limit sits

The combi's virtues follow from having no tank. It occupies a fraction of the floor area, mounts on a wall, and needs no separate water-heating appliance, which makes it the natural fit for townhouses, condos, secondary suites and compact homes where every square foot is spoken for. Because it produces hot water only on demand, it does not spend fuel holding a reservoir at temperature through the day, and in a household whose draws are short and sequential, one well-sized combi quietly covers every event.

The limit is instantaneous flow. Delivery depends on how much heat the burner can put into the water and how cold the incoming supply is, and in winter the same boiler delivers less hot water per minute than it does in summer. A single shower is comfortably within range for most correctly sized combis; two showers plus a dishwasher at the same moment can exceed what the appliance can deliver, and the temperature at the fixtures begins to drop. Manufacturers publish continuous-delivery figures precisely so buyers can test the appliance against the household's real draw pattern, and the model pages on this site list the published figures for each documented unit.

Why a boiler with an indirect tank still suits larger homes

The heating-only boiler plus indirect tank keeps the two jobs separate in time. The tank holds hot water produced earlier, so a big draw does not need the boiler to be firing at full rate at that exact minute. Recovery happens between uses, often at a modest firing rate, and a large soaker-tub fill or several simultaneous showers draws down the reserve rather than overwhelming the burner. Households with several bathrooms, frequent guests, or commercial-style draw patterns are the classic candidates, and the arrangement is also the least disruptive path when a home already has a sound storage tank and good plumbing.

The trade-offs are space, first cost and a longer chain of parts: the tank stands beside the boiler, the two are connected with piping, a circulator and priority controls, and both the tank and the boiler need room to breathe and be serviced. Because the boiler reheats the tank, a boiler outage also pauses hot-water production until the unit is repaired, a single-point dependency the combi shares, with the difference that the stored volume keeps serving draws in the meantime.

Combi boiler versus heating-only boiler with an indirect tank, in words
CharacteristicCombi boilerHeating-only boiler with indirect tank
Hot-water productionOn demand, through a plate heat exchangerStored in an insulated tank, reheated by the boiler between uses
Space requiredOne wall-hung appliance; no tankBoiler plus a floor-standing tank
Simultaneous drawsLimited by the burner's delivery rate, which falls in winterServed from the stored reserve while the tank recovers
Very large tub fillsGenerally exceed a residential combi's continuous rateDrawn from storage, then recovered by the boiler
Hot water during a boiler outageNone until the unit is repairedStored volume continues until drawn down
Separate appliance to buyNo; the combi does both jobsYes; boiler and tank are separate purchases
Typical fitCompact homes, townhouses, suites with modest drawsDetached homes, larger households, high simultaneous demand

The decision factors that actually matter

The decisive questions are about the building and the household, not the brochure. Count the bathrooms and the largest realistic simultaneous draw, and note whether a slow recovery would be noticed. Measure the mechanical space, including access for service, because a tank needs floor area and clearance that a wall-hung unit does not. Consider whether the home already owns a sound indirect tank whose retention would simplify a boiler replacement, and whether the gas supply and vent route can support a unit that fires hard during hot-water draws, which a combi does and a heating-only boiler does not need to.

Efficiency ratings between the two arrangements come from different manufacturers and test conditions, and the difference that matters is operational: a modulating condensing appliance matched to the loads, running at cool return temperatures, condenses more than an oversized one idling at minimum fire. That argument applies with equal force to both configurations.

  • Choose a combi when tank space is scarce and draws are modest, short and mostly sequential
  • Choose a heating-only boiler with an indirect tank for several bathrooms, large tubs or real simultaneous demand
  • Size the hot-water side from fixtures and occupants, and the heating side from a heat-loss calculation, separately
  • Before deciding, confirm the gas supply, vent route and mechanical-room access for whichever arrangement is proposed

Sizing a combi and sizing a boiler with a tank are different calculations

Both arrangements have to meet the same two loads, and they meet them in different ways, which is why the sizing arithmetic differs. The space-heating side is the same for either: the output comes from a heat-loss calculation for the building, and it is stated separately from the hot-water load. It is the domestic side that splits the two.

A combi is sized as a flow problem. Its hot water is made as it flows, so what matters is the largest realistic simultaneous draw, such as two showers and a dishwasher at once, measured against the appliance's continuous delivery at the coldest incoming water temperature the home sees. Delivery is a temperature rise at a flow rate, so the same unit delivers less hot water per minute in January than in September, and a combi that covers the household in summer can fall short in winter. Counting bathrooms alone does not size a combi; the draw pattern and the winter supply temperature do.

A boiler with an indirect tank is sized from stored volume plus recovery. The tank holds a reserve that serves a large draw as it happens, and the boiler reheats it between draws at a rate the coil and the boiler's output allow. Manufacturer literature describes the combined figure as the first-hour rating, because what matters is not the tank's gallons alone but how much hot water the arrangement can deliver in its busiest hour. A tank that is large enough but paired with a boiler that recovers slowly can still run cool late in a heavy morning.

How each arrangement is sized
QuestionCombi boilerHeating-only boiler with indirect tank
Space-heating sideOutput from a heat-loss calculationOutput from a heat-loss calculation
Domestic sideContinuous flow at the required temperature riseStored volume plus the boiler's recovery rate
Worst case to design forLargest simultaneous draw on the coldest incoming supplyTotal hot water drawn in the busiest hour
What changes the answerIncoming water temperature, fixture flow rates, unit capacityTank size, boiler recovery, coil performance
How it fails when undersizedTemperature drops during a simultaneous drawHot water runs cool late in a heavy draw

Vent, gas supply, condensate and space: what each arrangement needs installed

Because both arrangements are condensing gas appliances, the boiler side is similar: a sealed combustion appliance venting in certified plastic pipe to an approved exterior terminal, a gas connection sized to its input, a condensate drain, and an electrical supply for its controls, fan and ignition. The difference is what the domestic hot water adds.

A combi concentrates everything in one cabinet. It has one vent, one gas connection, one condensate path and one electrical supply, and its domestic-water connections are made at the appliance itself. That is why it suits a wall in a small mechanical space. The trade is that every domestic-water component sits inside the same cabinet, so a hot-water fault is diagnosed on the appliance.

A heating-only boiler with an indirect tank keeps the combustion appliance and the storage vessel separate. The tank has no burner, flue or gas connection of its own, so it adds no second vent and no second gas line. What it adds is floor area, a coil circuit piped to the boiler, a circulator and priority control so the tank and the heating zones do not call at once, and usually a mixing valve to limit the water temperature delivered to fixtures. The boiler still carries the vent, the gas supply and the condensate.

The practical consequence for a quote is that a tank adds scope even though it adds no combustion. Moving from a combi to a boiler with a tank brings piping, a circulator and controls that were not there before, and moving the other way removes them. Either direction is a system change under British Columbia's gas permit and inspection system, and strata or duplex owners use a licensed contractor who applies for the permit.

What each arrangement needs installed
RequirementCombi boilerHeating-only boiler with indirect tank
VentingOne sealed plastic vent to an exterior terminalOne sealed plastic vent on the boiler; the tank adds none
Gas supplyOne connection at the applianceOne connection at the boiler; the tank adds none
CondensateDrained from the applianceDrained from the boiler; the tank produces none
Domestic-water connectionsAt the appliance, through its plate heat exchangerAt the tank, through its coil circuit
Floor spaceWall-hung; no tankBoiler plus a floor-standing tank with service clearance
Extra controls and pipingContained in the applianceCirculator, priority control and a mixing valve at the tank

Cost, repair and emergency differences

The two arrangements carry different scope, and scope, not a single headline number, is what makes one project larger than another. Boilers.ca publishes no prices, and a firm figure comes only from an assessment. What can be compared honestly is what each arrangement contains. A combi concentrates its pump, expansion vessel, plate heat exchanger and domestic-water controls inside one cabinet, while a heating-only boiler with an indirect tank spreads those functions across a boiler, a floor-standing tank, a circulator and priority controls, together with the piping and wiring that connect them. More connected components usually mean more material and more labour to install or replace, even when the boiler itself is a smaller part of the system.

The differences surface again in service. On a combi, hot-water faults — a sticking diverter, a scaled plate exchanger, a flow sensor that misreads — are diagnosed inside the one appliance, which makes them combi-specific repairs. On a system arrangement the same symptom can originate in the tank, its coil, its aquastat, a zone valve or the boiler itself, so diagnosis has to separate the parts. Resilience differs too, and it is worth weighing before winter: if a combi locks out, the home loses heating and hot water at the same moment, whereas a stored tank keeps delivering hot water from its reserve for a time after the boiler stops, even though the home is without heat. Both arrangements require annual servicing — commonly a condition of the manufacturer's warranty and, as FortisBC advises, best handled by a licensed gas contractor.

A household-by-household way to decide

Brochure comparisons list features; households are decided by draw patterns and floor space. The table below maps the situations that come up most often in Greater Vancouver onto the arrangement that usually suits them, and it is the same logic the consultation service on this site works through before any equipment is proposed. It is a starting point, not a substitute for an assessment, because the existing system, the gas supply and the mechanical room each change the answer.

Common Greater Vancouver situations and the arrangement that usually fits
Household and homeUsually fitsWhy
Townhouse or condo, one or two bathrooms, staggered morning drawsCombi boilerNo tank space, and short sequential draws stay within the unit's continuous delivery rate
Compact home, laneway house or home with a secondary suiteCombi boilerWall-hung footprint suits a small mechanical space; the hot-water side is sized to the suite's demand
Detached home, three or more bathrooms, frequent overlapping drawsHeating-only boiler with indirect tankThe stored reserve serves simultaneous draws while the tank recovers between them
Home with a large soaker tub or frequent guestsHeating-only boiler with indirect tankA large fill draws from storage rather than from the burner's continuous rate
Home that already owns a sound indirect tank and is replacing the boilerHeating-only boiler with indirect tankKeeping a sound tank removes a major scope item from the project
Strata building served by a shared plantBuilding plant, not a single applianceShared systems are designed as a whole; in-suite changes run through the contractor and the building's approval process

Five myths about combi and system boilers in BC

The labels carry more folklore than engineering, and clearing the common claims is a useful part of the decision. First, a combi is not automatically more efficient than a boiler with a tank. A tank carries some standing loss between uses, and a combi avoids it, but a combi also fires hard during every hot-water draw; the result depends on the models, the controls and how well each is matched to the load rather than on the absence of a tank. Second, a heating-only boiler is not a lesser appliance. It does one job, and in many homes it does that job with less domestic-water hardware inside the cabinet.

Third, a combi is not only for one person. It serves plenty of families whose hot-water events are short and sequential; what it cannot do is exceed its continuous delivery rate, and the winter supply temperature is what lowers that rate. Fourth, a boiler with a tank is not wasting energy all day. An insulated tank loses some heat between uses, but recovering it at a modest firing rate is exactly the long, gentle run a modulating condensing appliance is designed for. Fifth, switching between the two is not a simple swap. It is a system change that can add or remove a tank, its piping, a circulator and priority controls, alter the domestic-water connections, and require the venting and gas supply to suit the new appliance — and in BC the gas work requires a permit and inspection under Technical Safety BC, with strata and duplex owners using a licensed contractor.

How to tell which arrangement your home already has

Before comparing the two, it helps to identify what is installed today. Look beside the boiler for a tall insulated cylinder. An indirect tank means the home stores hot water and the boiler reheats it through a coil. If there is no tank and the wall-hung appliance carries its own domestic-water connections, it is a combi making hot water on demand.

The rating plate settles the question. Every gas boiler carries a model number, and the series pages on this site record whether a documented line is a combi or heating-only. Reading the plate also gives the input rating and the appliance type, both of which any replacement quote and the gas permit depend on.

The vent count is a further clue. A sealed condensing appliance vents through certified plastic pipe to one terminal. An indirect tank adds no flue of its own because it has no burner. So one plastic vent with a tank beside the boiler points to a heating-only boiler with an indirect tank, while one plastic vent, no tank and domestic pipes on the appliance points to a combi. None of this requires opening the casing or touching gas piping; the model number and the presence of a tank are visible from outside, and anything beyond that belongs to a licensed technician.

On-demand or stored: where 'tankless' fits

The word 'tankless' describes on-demand production, and in a hydronic home that role is filled by a combi: it heats domestic water as it flows and stores none. Stored hot water is the indirect-tank arrangement, where the boiler reheats a reserve that the household draws from. In a home that already heats with water, 'tankless versus storage' and 'combi versus system' are two ways of naming the same decision.

That is why the comparison of delivery, space and simultaneous draws in this guide applies to both phrasings. What changes with the words is only the starting point: 'tankless' begins from the on-demand side, and 'storage' begins from the reserve.

A standalone tankless water heater is a different appliance again. It has its own burner and vent, makes hot water on demand, and does not heat the home, so it sits outside the space-heating decision. The choice in a boiler home remains whether domestic water is made on demand or kept in reserve.

The supply side: why mains flow and pressure matter

A combi makes hot water from the water main the moment a tap opens, so its delivery depends on more than the appliance. The incoming water temperature sets how much the burner has to raise it, and the incoming flow and pressure set how much water is available to heat. A home with low mains pressure, a long service run or shared plumbing can limit what any combi delivers, whatever its rating says.

A stored arrangement is more forgiving of a momentary supply problem. The tank fills over time and holds its reserve, so a brief dip in mains pressure does not change the temperature at the shower. That is one reason larger homes and buildings tend to store.

An assessment checks the incoming supply against the appliance's documented requirements before a combi is proposed. It is also why two homes with the same number of bathrooms can need different answers.

What changes in the house during a switch

Switching between the two is a system change, not an appliance swap. Moving from stored to on-demand removes the tank, its piping, its circulator and its priority controls, and adds domestic-water connections at the appliance. Moving the other way adds all of them back. The venting and gas supply must suit the new unit, and the loop must be checked for the flow the new arrangement expects.

Because it is gas work, the change runs under British Columbia's permit and inspection system through Technical Safety BC, and strata or duplex owners use a licensed contractor. The sequence is the same as any boiler project: identify what is there, calculate the heating and hot-water loads separately, choose the arrangement, then confirm the gas supply, vent route and mechanical space before any equipment is ordered.

Recirculation loops and how quickly hot water arrives

How long a tap takes to run hot is a plumbing question as much as an appliance question. Hot water sitting in the pipe between the boiler and the fixture cools between uses, so the first draw pushes that cooled water out before hot water arrives. A recirculation loop addresses this by keeping a small flow moving through the hot-water piping, or by returning cooled water to the heat source, so the run stays primed.

The two arrangements relate to a loop differently. A stored arrangement has a tank to return water to, so a recirculation loop fits naturally around it and the tank simply holds the temperature. A combi makes hot water only when there is a draw and holds no tank to circulate, so where a home already has a recirculation loop the assessment has to confirm how the chosen appliance is designed to work with it. That is a question for the manufacturer's documentation and the installer, not something to assume either way.

For a home without a loop, the honest way to compare the two is to time the actual run at the fixtures the household uses most, rather than to rely on a general claim about wait times. The result depends on the length and insulation of the pipe run and on whether a loop exists, and it is one of the practical questions the consultation service on this site works through before equipment is proposed.

Two households under one roof: a secondary suite

A secondary suite changes the hot-water calculation more than it changes the heating calculation, because two households tend to draw hot water at the same times of day. Where a single appliance serves both, the suite's demand is added to the main household's before the hot-water side is sized, whether that means a larger combi or a tank and boiler sized for the combined peak.

There are two broad ways to serve a home with a suite. One appliance can cover both households, which keeps the equipment count and the maintenance to one system but means a failure affects everyone at once. Alternatively, the suite can have its own appliance, which makes each household independent but adds a second gas appliance to install, permit and service. Which is better depends on the suite's demand, the space available and how much independence the owner wants.

The choice of arrangement then follows the same logic as any other home once the demand is totalled. A suite with short, sequential draws and no room for a tank can suit a combi, while a suite added to a household that already stores hot water may be better served by enlarging the stored arrangement. Strata and duplex owners cannot use Technical Safety BC's homeowner gas permit route, so the work runs through a licensed contractor who applies for the permit, and where the two households share a system the change is scheduled so neither is left without heat or hot water.

Which arrangement fits a Greater Vancouver home

The housing stock usually narrows the choice before cost does. Townhouses, laneway houses, secondary suites and compact detached homes in the City of Vancouver, Burnaby, Richmond, Coquitlam and the North Shore tend to favour a combi: the appliance is wall-hung, needs no tank, and suits households whose hot-water draws are short and mostly sequential. Detached homes in Vancouver, Surrey, Langley and the Tri-Cities with several bathrooms, a large soaker tub or frequent overlapping draws are the classic candidates for a heating-only boiler with an indirect tank, and a home that already owns a sound tank often keeps it. Strata buildings add their own layer: an in-suite combi change runs through a licensed contractor and the building's approval process, while a shared plant serving many units is a different project altogether.

The coastal climate does not separate the two. Greater Vancouver's long, mild shoulder seasons reward a modulating condensing appliance that spends its time at low fire and cool return temperatures, and that argument applies equally to a combi and to a boiler reheating a tank. What the climate does change is the hot-water calculation: incoming mains water is colder in winter, which lowers a combi's delivery rate exactly when the heating load is highest, and that is the number to check against the household's real morning pattern. The consultation service on this site works through that pattern, the available space and the existing system before equipment is proposed.

Installation and permitting realities

Either arrangement is gas work: in BC, installing or replacing the boiler requires a gas permit and inspection under Technical Safety BC, homeowners in single-family homes may hold the permit in the cases Technical Safety BC describes, and owners of strata units and duplexes must use a licensed contractor who applies for it. Some municipalities issue their own gas or heating permits for single-family and duplex dwellings, so the contractor confirms which authority issues the permit for the property before work begins.

The indirect-tank side adds plumbing beyond the boiler: tank piping, a circulator and priority control so the tank and heating zones do not fight over the boiler, and a check that tank recovery does not push the return temperature so high that a condensing boiler stops condensing. A combi instead concentrates everything in one cabinet with its own pump and expansion vessel, which the installer verifies against the home's loop. Boilers.ca sells and installs both configurations with ROMA Heating & Cooling in Greater Vancouver; the consultation service works through draw patterns and space before any equipment is proposed, and the instant estimator gives a ballpark range to open the conversation.

Models referenced in this guide

IBC Technologies

IBC SFC 125-1 Superflow

CurrentSold in Canada
Input
16.5–99 MBH
Output (max)
89 MBH
AFUE
95 %

The IBC SFC 125-1 Superflow is a wall-hung condensing combi boiler rated 95% AFUE: up to 99 MBH for space heating and 125 MBH for domestic hot water, with 3.2 GPM continuous DHW delivery at a 67°F rise.

Natural gasPropaneCombi

IBC Technologies

IBC SL 14-115 G3

CurrentSold in Canada
Input
14–115 MBH
Output (max)
109 MBH
AFUE
95 %

The IBC SL 14-115 G3 is a wall-hung residential condensing boiler with a 14 to 115 MBH input range and 95% AFUE, running on natural gas or propane. It is the size most often matched to a typical Lower Mainland detached home with radiators or in-floor heat.

Natural gasPropaneHeating-only

Frequently asked questions

Does a combi boiler ever run out of hot water?

It has no tank to empty, so it never 'runs out' in the storage sense, but it delivers only up to its continuous flow rate. Exceed that with simultaneous draws, and the water at the fixtures cools; winter's colder supply lowers the limit.

Is a combi more efficient than a boiler with a tank?

Not by definition. Stored tanks lose some heat between uses while combis avoid that standing loss, but combis fire harder for hot water and ratings differ by model. Matching the appliance to the household's pattern matters more than the headline comparison.

Can an indirect tank be added to an existing boiler later?

Often yes, if the boiler is a heating-only unit whose controls support a tank call and the piping and circulator are added correctly. Whether your particular boiler can drive an indirect tank is confirmed from its manual and a site assessment.

Is a system boiler just a boiler with a hot-water tank?

In the BC market, effectively yes: the arrangement is a heating-only boiler connected to an indirect storage tank, and hot water is drawn from the tank. The term 'system boiler' itself is British and also implies that the pump and expansion vessel are built into the appliance.

Which costs less to install in Greater Vancouver, a combi or a boiler with a tank?

Boilers.ca publishes no prices, and the answer follows scope rather than the appliance. A combi removes the tank but places all the domestic-water components inside one cabinet that is serviced as a unit; a boiler-and-tank arrangement adds a tank, a circulator, priority controls and the piping between them. An on-site assessment produces the actual quote for either path.

Can a home switch from a combi to a boiler with an indirect tank, or the reverse?

Often yes, but it is a system change rather than a simple swap: switching adds or removes a tank and its piping, controls and domestic-water connections, and the venting and gas supply must suit the new appliance. An assessment confirms whether the change suits the home.

Is a system boiler better than a combi boiler?

Neither is better in the abstract. A heating-only boiler with an indirect tank suits homes where several bathrooms or a large tub create real simultaneous demand and floor space allows a tank; a combi suits homes where space is scarce and hot-water draws are short and sequential. The household's draw pattern and the available space decide.

Which is cheaper to run, a combi or a boiler with a tank?

Running cost depends on the models, the controls and how well the arrangement is matched to the load, not on the label alone. A combi avoids the tank's standing loss but fires hard for hot water, while a boiler recovers a tank at a modest rate. An assessment of the household's draw pattern is the honest basis for the comparison.

How can I tell whether I have a combi or a system boiler?

Look for a hot-water tank beside the boiler. If there is one, the home stores hot water and the boiler reheats it; if there is no tank and the appliance carries its own domestic-water connections, it is a combi. The model number on the rating plate confirms it, and the series pages on this site record whether a documented line is a combi or heating-only.

Does mains water pressure affect a combi boiler?

Yes. A combi heats water from the main as it flows, so the incoming flow and pressure, along with the incoming water temperature, limit what it can deliver. A stored arrangement buffers those swings because the tank fills over time. An assessment checks the incoming supply against the appliance's documented requirements.

What is the difference between a tankless boiler and a storage boiler?

In a hydronic home, 'tankless' means on-demand domestic hot water, which is what a combi provides, while 'storage' means a boiler reheating an indirect tank that the household draws from. They are the same choice as combi versus system, named by whether hot water is made on demand or kept in reserve.

How is a combi boiler sized differently from a boiler with a tank?

A combi is sized as a flow problem: the largest simultaneous hot-water draw at the coldest incoming water temperature, not the number of bathrooms. A boiler with an indirect tank is sized from stored volume plus recovery, often expressed as a first-hour rating. Both need the space-heating load calculated separately from a heat-loss calculation.

Does a boiler with an indirect tank need a second vent or gas line?

No. The tank has no burner, flue or gas connection of its own, so the boiler still carries the one vent and the one gas connection. The tank adds floor space, a coil circuit, a circulator, priority control and usually a mixing valve, which is why it is a system change rather than a simple appliance swap.

Does a combi boiler work with a hot-water recirculation loop?

It depends on the appliance, and the answer comes from the manufacturer's documentation rather than from a general rule. A stored tank has a reservoir to return water to, so a recirculation loop fits naturally around it; a combi holds no tank to circulate, so its ability to work with a loop is confirmed for the specific model during the assessment.

Is a combi or a boiler with a tank better for a home with a secondary suite?

It depends on the suite's demand and the space available. If one appliance serves both households, the suite's demand is added to the main household's before the hot-water side is sized. A suite with short, sequential draws and no room for a tank can suit a combi; a household that already stores hot water may be better served by enlarging the stored arrangement, or by giving the suite its own appliance for independence.

Get a ballpark estimate in two minutes

Answer a few questions for a CAD range before you share any contact details.

On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.

Guides

Sources and verification

Facts checked September 15, 2026. Last updated September 15, 2026. Technical reviewer: not yet assigned.

CallEmailEstimate