Slant/Fin VSPH-60
The Slant/Fin Victory VSPH-60 is the smallest VSPH: a discontinued, NON-condensing cast-iron, floor-standing direct-vent boiler with 60,000 Btuh fixed input across 3 cast-iron sections, venting in 3" AL29-4C stainless steel to 40 ft at all altitudes.
Key figures
- Max input
- 60 MBH
- Max CSA output
- —
- AFUE
- —
- Min input
- —
Input is gas energy consumed; output is heat delivered. Never size from input alone.
Slant/Fin VSPH-60 in practice
The VSPH-60 is the entry size of the Victory VSPH series — a cast-iron, gas-fired, floor-standing boiler that is NOT condensing and NOT wall-hung. It fires a fixed 60,000 Btuh across 3 cast-iron sections (metal push nipples, ASME 'H' stamp) in a mechanically induced-draft, sealed-combustion direct-vent design whose positive-pressure flue must be 3" UL-listed AL29-4C stainless steel. Its jacket width (A) is 11-1/8" with dimension B 17-3/8" per the manual's Figure 1 (+1-1/2" height and 28-1/2" depth with the combustible floor kit).
The I&O venting table allows 40 ft maximum equivalent flue length on Heat-Fab Saf-T / EZ Seal systems at all altitudes to 10,000 ft for this size (air intake 40 ft), with shorter runs on other listed systems such as ProTech FasNSeal (30 ft). The HydroStat 3000 control (DOE-2012 compliant, LED diagnostics) runs the burner on natural gas or field-converted LP, at 50 psi ASME MAWP with a 30 psi relief valve.
Slant/Fin lists the VSPH under 'Vintage' and the line is discontinued, and the official library page hosts 2018 heat-exchanger RECALL notices — owners of a VSPH-60 must check those notices for their unit's date range. canadianStatus stays 'unknown' (no official Canadian-sales statement found); all gas, venting and combustion work belongs with a licensed contractor.
Best suited to
- Smaller homes with a 60,000 Btuh-class direct-vent load already installed and vented in stainless steel
- Owners of an installed VSPH-60 confirming ratings and the recall status of their unit
- Contractors documenting the discontinued cast-iron direct-vent generation
Applicability and support
- Model number
- VSPH-60
- Canadian availability
- unknown
- Production status
- discontinued
- ROMA supplies
- Confirmed at consultation
- ROMA services
- Confirmed at consultation
- Warranty
- Series terms
Where ROMA provides on-site service
On-site service is currently offered in Greater Vancouver, BC, including Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Port Coquitlam, Port Moody, Delta, Langley, Maple Ridge, Abbotsford, Chilliwack, White Rock, Pitt Meadows, Tsawwassen, Anmore, Lions Bay, Belcarra, Bowen Island, Mission. Everything else on this site is reference information you can use anywhere in Canada.
Specifications
Published specifications
Values as published by Slant/Fin. Units are shown with every value; notes flag conflicting sources or missing figures.
| Specification | Value | Note |
|---|---|---|
| Input | ||
| Input | 60 MBH | 60,000 Btuh fixed gas input per the ratings and dimensions data in the VSPH I&O manual (Pub. VSPH-41 Rev. C). |
| Domestic hot water | ||
| Domestic hot water | Heating-only boiler — domestic hot water comes from a separate indirect water heater (indirect connections supported by the control) | |
| Venting and air | ||
| Venting | Direct vent, sealed combustion — mechanically induced draft, positive-pressure flue: 3" diameter UL-listed AL29-4C stainless steel only (Heat-Fab Saf-T Vent / Saf-T EZ Seal, ProTech FasNSeal, Flex-L StaR-34 or Z-Flex Z-Vent); NO PVC/plastic or galvanized flue; no vent damper; common venting not allowed | Minimum flue length 2 ft; max equivalent lengths by model and vent-system manufacturer. Combustion air intake: 3" PVC Schedule 40 or galvanized steel. Flue gas may partially condense in the blower discharge — the boiler has a factory condensate drain and water trap. |
| Max. flue equivalent length (Heat-Fab Saf-T / EZ Seal) | 40 ft at all altitudes | By elevation band 0–5,000 / 5,000–7,500 / 7,500–10,000 ft per the I&O manual's venting table; other listed systems allow shorter runs (e.g. ProTech FasNSeal). |
| Physical and connections | ||
| Cast-iron sections | 3 | Cast-iron sections assembled with metal push nipples (ASME 'H' stamp), per the VSPH I&O manual Figure 1. |
| Operating limits and other | ||
| Fuel | Natural gas or propane | Field-convertible NG-to-LP gas valve; orifice chart covers elevations to 10,000 ft (4% derate per 1,000 ft). |
| Maximum allowable working pressure (MAWP) | 50 psi | 50 psi ASME working pressure with a factory-supplied 30 psi safety relief valve, per the VSPH master specification. |
Manuals
- Victory VSPH Series Installation and Operating Instructions — Pub. VSPH-41 Rev. C (P/N 455056)VSPH-41 Rev. C (P/N 455056) · 2019-08
Alerts documented for this model
Frequently asked questions
Is the VSPH-60 a condensing boiler?
No. It is a non-condensing cast-iron boiler with a mechanically induced-draft, sealed-combustion direct-vent flue in 3" AL29-4C stainless steel; the factory condensate drain handles partial condensation in the blower discharge.
How much does the VSPH-60 input?
60,000 Btuh fixed input (60 MBH) across 3 cast-iron sections, per the VSPH I&O manual.
Was the VSPH-60 recalled?
Slant/Fin's official library hosts 2018 VSPH recall notices (contractor and homeowner) covering a heat-exchanger recall; owners should check whether their serial/date range is affected.
Questions about the Slant/Fin VSPH-60?
Describe what the boiler is doing and get a straight answer about the next step.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- Slant/Fin — library: Victory VSPH series (Vintage; manuals and recall notices) · accessed September 8, 2026
- Victory VSPH Series Installation and Operating Instructions — Pub. VSPH-41 Rev. C (P/N 455056) (PDF) · VSPH-41 Rev. C · accessed September 8, 2026
Facts checked September 8, 2026. Last updated September 8, 2026. Technical reviewer: not yet assigned.