Viessmann Vitodens 100-W F.468 — Ionization Current Too High during Calibration
F.468
Ionization current too high during calibration. The ionization current is too high during calibration; check the gap between the ionization electrode and the flame body assembly and check for a lot of dust in the ventilation air, then reset the boiler.
If a carbon-monoxide alarm sounds
- Leave the building immediately and get fresh air.
- Call 911. Do not go back inside until emergency services say it is safe.
- Have every fuel-burning appliance inspected before use.
Only after that, call ROMA about the boiler. Official guidance: Health Canada on carbon monoxide.
Applies to
This venting or air-supply fault code is displayed by the HMU-BCU control (3.5" display) on Vitodens 100-W B1HE heating-only and B1KE combi models (B1HE-85, B1HE-120, B1HE-150, B1HE-199, B1KE-120, B1KE-199), as documented in Installation and Service Instructions — Vitodens 100-W B1HE/B1KE, doc 6167 818 - 22, troubleshooting fault messages (6167 818 - 22). Codes can differ between controller generations, so always check the manual that matches your unit.
- Viessmann Vitodens 100-W (B1HE / B1KE)
- Viessmann Vitodens 100-W B1HE-85
- Viessmann Vitodens 100-W B1HE-120
- Viessmann Vitodens 100-W B1HE-150
- Viessmann Vitodens 100-W B1HE-199
- Viessmann Vitodens 100-W B1KE-120
- Viessmann Vitodens 100-W B1KE-199
Controller: HMU-BCU control (3.5" display). Source manual: 6167 818 - 22 (2026-02).
Why a code is not a diagnosis
A venting or air-supply code points at the combustion-air path: a blocked terminal, a restricted flue, a failed fan, or a condensate restriction. It does not say which, and running an appliance with a blocked flue is unsafe.
Safe things to observe
- If a carbon-monoxide alarm sounds anywhere in the building, leave immediately and call 911 from outside.
- From a safe distance, check that the vent terminal and combustion-air inlet are not blocked.
- Do not run the appliance while a blockage is suspected.
Do not
- Do not put anything into the vent or air-intake openings.
- Do not remove or modify vent pipe.
How professional service helps
- A technician inspects the full vent and combustion-air path, clears blockages and checks the fan.
- Combustion and safety devices are verified with an analyser and the manufacturer's procedure after any repair.
Where ROMA provides on-site service
On-site service is currently offered in Greater Vancouver, BC, including Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Port Coquitlam, Port Moody, Delta, Langley, Maple Ridge, Abbotsford, Chilliwack, White Rock, Pitt Meadows, Tsawwassen, Anmore, Lions Bay, Belcarra, Bowen Island, Mission. Everything else on this site is reference information you can use anywhere in Canada.
Parts and service
Parts commonly involved
These parts appear in the documented text for this alert. A code reports a condition, not a failed part — a technician confirms the cause by testing before anything is replaced.
Ignition electrode
The ignition electrode creates the spark that lights the burner in a gas boiler, and on many models it also senses the flame once it is burning.
What a technician checks →
Service for this alert
- Gas Boiler Repair
Licensed gas technicians from ROMA Heating & Cooling diagnose and repair residential and light-commercial gas boilers across…
Every boiler part explained — what it does, how it fails and what a technician checks.
Documented for Viessmann Vitodens 100-W (B1HE / B1KE).
Frequently asked questions
Is this code a carbon-monoxide danger?
The code relates to combustion or venting, so treat any CO alarm as an emergency and call 911 from outside. The appliance itself should be checked by a technician before it runs again.
Can I clear this code myself?
Clearing a code without fixing its cause usually just brings it back. Note the code, check the safe items on this page, then call a licensed technician. If your appliance manual describes a user reset for this exact code and it stays away, no call may be needed.
Boiler locked out? Call with the alert text ready.
The brand, model and this alert are passed along when you request service online, so the technician arrives prepared.
On-site service in Greater Vancouver, BC. ROMA lists “Open 7 days” on its site; call to confirm same-day availability.
Sources and verification
- Installation and Service Instructions — Vitodens 100-W B1HE/B1KE, doc 6167 818 - 22, troubleshooting fault messages · 6167 818 - 22 · accessed September 7, 2026
Facts checked September 7, 2026. Last updated September 7, 2026. Technical reviewer: not yet assigned.